Bryston SP3 Скачать руководство пользователя

Страница: 7 / 72

F: MAIN / ZONE SELECT

The SP3 can send a different

stereo

audio source

signal to its ZONE outputs (Zone 2 Out) than to its main

outputs (Single Ended Outputs or Balanced Outputs).

Pressing the MAIN button allows selection of the signal

that will go to the Single Ended Outputs and Balanced

Outputs using the source select buttons (item “G”) while

pressing ZONE allows the same source select buttons to

set the signals that will be sent to the Zone 2 Out outputs)

G: SOURCE (INPUT) SELECT BUTTONS

Ten buttons for selecting audio input source signals (see

”F” above). When HDMI is selected (LED above HDMI

button is ON) the first 8 source select buttons (

DVD,

CBL/SAT, TUNER, CD, DVR, TAPE, BAL-1, BAL-2

)

represent HDMI inputs 1 through 8 respectively. When

MAIN

is selected, source signal selected will appear at

the

MAIN

outputs. When

ZONE

is selected, the source

signal selected will appear at the

ZONE 2 OUT

outputs

H: STANDBY BUTTON

Places the unit in standby mode. Status indicator LED is

normally off when unit is operating. It turns red when unit

is placed in standby mode. When uploading new soft-

ware it may blink off and on in different colours. The spe-

cifics of theses different colour states is significant only to

engineering and service personel.

Power consumption in Standby mode is <1 Watt.

SP3 PREAMP / PROCESSOR

Содержание SP3









































































Результаты поиска

Содержание SP3

Отзывы:

Похожие инструкции для SP3

Бренды по названию

Популярные бренды

Bryston SP3, Руководство пользователя

Результаты поиска

Содержание SP3

Отзывы:

Похожие инструкции для SP3

Бренды по названию

Популярные бренды