Bryston SP3 Скачать руководство пользователя страница 69

Страница: 69 / 72

SP3 PREAMP / PROCESSOR

SP3 IDLE SCREEN EXPLANATIONS

Page 1 of 3

SP3 IDLE SCREEN EXPLANATIONS

2011-11-24

SP3 DEFAULT SCREEN

1. Default screen, playing SPDIF input, PCM-encoded 2 channel stream, example

Line1: SRC: AES1 DIG

Line2: IN: PCM 44k 2/0

Line3: OUT: PL2xMovie 2/2/2.0

Line4: VOLUME: -21.0dB

Using SPDIF balanced digital source BAL1+DIGITAL, playing two channel audio file from BDP-1

The center speaker was configured as NONE and the rest were declared as LARGE. The “.0” ending

indicates that the subwoofer is not being used (in spite being declared as present), since the bass is

reproduced through the large front speakers. If all speakers including center were present, then the short

7.0 would have been displayed instead of the full 3/2/2.0 in such a case. If the front speakers were declared

as SMALL then the bass would have been reproduced through the subwoofer and 2/2/2.1 would have been

shown instead of 2/2/2.0

Source

Input type (digital, analog, hdmi, bypass)

Program encoding: linear PCM 2ch

Sample rate (kHz)

Program format (front/surr/back.lfe)

Surround re-creation mode: Dolby ProLogic IIx “Movie”

Listening format

(front/surr/back.subwoof)

Output volume control (level in dB)

APPENDIX M

IDLE SCREEN EXPLANATIONS

Содержание SP3









































































Результаты поиска

Содержание SP3

Отзывы:

Бренды по названию

Популярные бренды

Bryston SP3, Руководство пользователя

Результаты поиска

Содержание SP3

Отзывы:

Бренды по названию

Популярные бренды