Bryston SP3 Скачать руководство пользователя

Страница: 50 / 72

APPENDIX

: DOLBY VOLUME/DRC SET continued

SP3 Dolby Volume/DRC Screen

Page 2 of 3

Dd VOL HIGH FULL MODE - Dolby Volume is ON, high strength (dynamic

range is highly reduced). The “Full Mode” means that Dolby

Volume algorithm applies both audio compression and spectral

equalization.

Dd VOL LOW HALF MODE - Dolby Volume is ON, low strength (dynamic

range is slightly reduced). The “Half Mode” (as opposed to “Full

Mode”) means that Dolby Volume algorithm applies only audio

compression but not spectral equalization.

Dd VOL MED HALF MODE - Dolby Volume is ON, medium strength

(dynamic range is moderately reduced). The “Half Mode” means

that Dolby Volume algorithm applies only audio compression but

not spectral equalization.

Dd VOL HIGH HALF MODE - Dolby Volume is ON, medium strength

(dynamic range is moderately reduced). The “Half Mode” means

that Dolby Volume algorithm applies only audio compression but

not spectral equalization.

DYN RANGE MEDIUM 1

– Dolby Volume is OFF but older DRC algorithm

(Dynamic Range Compression) is ON resulting in medium

dynamic range (moderate compression)

DYN RANGE LOW 2

– Dolby Volume is OFF, DRC is ON producing low

dynamic range (high compression).

DRC AUTO(THD,DTSHD) – Dolby Volume is OFF, DRC is ON, high

compression conditional upon the presence of DYNF flag in the

digital source stream.

3. Additional configuration options for Dolby Volume.

When any of the Dolby Volume selection is made, that is if line 2 selects anything from

Dd VOL LOW FULL MODE to Dd VOL HIGH HALF MODE (and only those) then

the additional configuration settings are displayed in the lines 3 and 4 on the screen:

Line 3: Dd VOL OFFS 0.0dB - use volume knob to adjust Dolby Volume level offset

–20.0..+20.0dB. This parameter defines the maximum sound level for the

This is equivalent to DYNAMIC RANGE MEDIUM selection in SP1.7, SP2

This is equivalent to DYNAMIC RANGE LOW selection in SP1.7, SP2

Содержание SP3









































































Результаты поиска

Содержание SP3

Отзывы:

Похожие инструкции для SP3

Бренды по названию

Популярные бренды

Bryston SP3, Руководство пользователя

Результаты поиска

Содержание SP3

Отзывы:

Похожие инструкции для SP3

Бренды по названию

Популярные бренды