Bryston SP3 Скачать руководство пользователя

Страница: 15 / 72

SP3 PREAMP / PROCESSOR

SPECIFICATIONS

PERFORMANCE SPECIFICATIONS

A/D Conversion:

24-Bit, 192 kHz Delta-Sigma

D/A Conversion:

24-Bit, up to 192 kHz Delta-Sigma

DSP Engine:

TI DA710

Power Supply:

Separate off-line standby PSU plus & main linear power supply with toroidal power transformer

utilizing multiple regulation stages.

Frequency Response:

20 Hz to 20 kHz +/- 0.25 dB

Low Frequency Cutoff:

0.3 Hz

(all speakers channels in Bypass mode)

1.8 Hz

(LARGE Speakers and SubWoofer in Analog, Digital or HDMI)

40-200 Hz (variable cutoff point; default 80 Hz) SMALL speakers, except SubWoofer, in

Analog, Digital or HDMI)

High Frequency Cutoff:

40-200 Hz (variable cutoff point; default 80 Hz) (SubWoofer in Analog, Digital or HDMI)

22 kHz

(all speakers, except SubWoofer, in Analog, Digital or HDMI)

180 kHz (all speaker channels in BYPASS)

THD+Noise:

< 0 .006% in DSP modes; < 0.0025% in Bypass mode 20Hz to 20kHz at maximum output level.

Signal-to-Noise Ratio:

105dB in DSP Modes; 110dB in 2ch Bypass Mode; 22 kHz bandwidth, Ref. 1 kHz at max. output

Input Level:

2 Vrms in DSP modes; 4 Vrms in Bypass Mode

Input Impedance:

50 kOhms for single-ended analog audio, 1K Ohms for balanced analog inputs

Output Level:

8 Vrms (16 Vrms Balanced) in DSP Modes; 10 Vrms (20 Vrms Balanced) in Bypass Mode.

Output Impedance:

110 Ohms

Bass Management:

2nd Order HP filter(x5), 4th Order LP filter 40 – 200 Hz Crossover Freq.

ELECTRICAL SPECIFICATIONS:

Power:

120, 220 & 240Vac models.

Maximum power consumption: 65 Watts

Standby power consumption: <500mWatt

INPUTS

Analog Audio:

4x stereo single ended/unbalanced pairs (CD, Tuner, Cable/Sat, DVD)

2x pairs single ended, unbalanced tape inputs (RCA)

2x pairs of Balanced XLR (female) inputs

Digital Audio:

4x coaxial (RCA) 75 Ohms (SPDIF),

3x Optical (TOSLINK)

2x AES/EBU inputs (XLR) 110 Ohms

MENU TREE NOTES continued:

or two back speakers. By turning the BACK speakers off,

the surround sound speaker configuration becomes “5.1”. By

choosing only 1 BACK speaker the configuration becomes

“6.1”.

Содержание SP3









































































Результаты поиска

Содержание SP3

Отзывы:

Похожие инструкции для SP3

Бренды по названию

Популярные бренды

Bryston SP3, Руководство пользователя

Результаты поиска

Содержание SP3

Отзывы:

Похожие инструкции для SP3

Бренды по названию

Популярные бренды