Bryston SP3 Скачать руководство пользователя

Страница: 46 / 72

SP3 to LAN Setup Guide Pg. 2 of 4

would also work (however, the actual IP address value is determined by the DHCP lease event and may

vary).

2. SP3 setup for static host and static SP3.

This setup uses peer-to-peer physical connection using a cross-over

Ethernet cable, connecting the

Ethernet port on the back of SP3 unit, directly to the second LAN2 card in the host PC. To set up the

SP3, press right arrow key to enter the menu system, then:

SYSTEM SETUP



MISCELLANEOUS

Scroll to the third screen down:

TCP/IP setup screen

Make sure that the setup screen looks on like above screen

. After making a new DHCP selection press

left arrow key to escape back to the main screen, then press STANDBY button and then again to power

up, to reset the SP3 unit.

3. Host PC setup for static IP address.

Ideally, a second network

interface card (LAN2) would

connect only to SP3, while

the main network card

(LAN) would maintain the

normal network and internet

connectivity. An example of

the interface configuration is

showed at the right:

Configuration of the

second network card

(LAN2) for SP3

connectivity in the

static IP scheme

Some network card allow using standard (non-cross-over) Ethernet cables.

It is possible to edit and change the Ipadr or Ipmsk values but it should not normally be needed.

APPENDIX G: SETUP USING LAN continued

Содержание SP3









































































Результаты поиска

Содержание SP3

Отзывы:

Похожие инструкции для SP3

Бренды по названию

Популярные бренды

Bryston SP3, Руководство пользователя

Результаты поиска

Содержание SP3

Отзывы:

Похожие инструкции для SP3

Бренды по названию

Популярные бренды