Bryston SP3 Скачать руководство пользователя

Страница: 58 / 72

SP3 Control via RS232 & TCP/IP

Page 1 of 7

SP3 control through RS232 and TCP/IP

Updated 2-Aug-2012

1. Bryston Serial Protocol command set for SP3.

SP3 receives control commands and responds back to the host controller following an

execution of each command. SP3 can also be configured

to automatically broadcast

automatic responses through RS232 or TCP/IP upon certain system events such as input

source switching or volume level setting from the front panel or by IR remote controller.

The following commands can be sent over RS232, RS485 (with a RS232/RS485

interface) and TCP/IP (using GET mechanism over port 80).

Command format

ASCII strings ended with carriage return (code 13) or dot (.).

#D1D2C1C2C3C4P1P2...<CR>

command start character (RS232 only, in TCP/IP use URL code %23 instead)

device category, one digit 1..f (for SP3 D1 must be 1)

RS485 device ID, 1 digit 0..f(dflt=0). D2=0 typically and can only be changed

through the front panel menu!

C1..C4 command name (4 chars) , typically uppercase ASCII letters.

P1,P2 parameters are two or more arbitrary ASCII characters.
<CR> Special end char, ASCII code 13 (RS232 only, in TCP/IP use dot ‘.’ instead)

RESPONSE FORMAT

The Response format is the same as commands, repeating the D1,D2,C and P bytes (P

bytes may carry either an actual status value or ?? in case of errors).

Example (TCP/IP):

%2310MPWR01. -

command: power up

MISCELLANEOUS



RS232 MODE=ON+AUTOFB, note that this option resides in a hidden screen.

To unlock the hidden screens got to the last miscellaneous screen and then press ZONE,DVD and TAPE

buttons, in this order

SP3 may have additional unsupported commands that are exceptions to Bryston Serial Protocol, for

example a common help displaying command is a single question mark character

or some test and

diagnostic commands that are implemented for the purpose of trouble-shooting. The special commands

should never be used by controllers and in automated remote control scripts since they are not guaranteed

to be supported in all future product revisions!

APPENDIX

SP3 CONTROL VIA RS232 & TCPIP

Содержание SP3









































































Результаты поиска

Содержание SP3

Отзывы:

Похожие инструкции для SP3

Бренды по названию

Популярные бренды

Bryston SP3, Руководство пользователя

Результаты поиска

Содержание SP3

Отзывы:

Похожие инструкции для SP3

Бренды по названию

Популярные бренды