Bryston SP3 Скачать руководство пользователя

Страница: 56 / 72

APPENDIX J: FIRMWARE UPLOAD INSTRUCTIONS continued

SP3 Software Upload Instructions

Page 5 of 6

Firmware revision 2012.11 and later do not automatically redefault internal configuration

parameters and setups, therefore upgrading from a firmware earlier than 2012.05e may

cause software errors after power up, if a parameter introduced in the latest revision did

not exist in the old revision being replaced. If that happens upgrade first to revision

2012.05e (

ftp://bryston.com/pub/firmware/sp3/2012.05e/SP3.bin

) which will reset all

parameters, and then upgrade to the latest firmware.

If the upload followed by self-programming fails for whatever reason

, then the system

reverts to factory default which has a suffix 'f', that is in this case the firmware revision

reads as f2012.05e (or earlier) but functionally it is identical to the firmware with 'u'

prefix. If the bootloader reverted the firmware to a factory backup, it is recommended to

upload the new firmware file again and to watch the sequence of events. The upload

should last about 1 minute, followed by a reboot (all automatic, it is not necessary to

press anything). Then the screen will remain dark for another minute or so, while the

standby LED begins flashing a multicolor codes - first a few short blink codes, followed

by about 1 second long yellow or magenta (erase stage) followed by a few seconds of

long red (self-programming stage). Then the system will attempt an automatic restart,

the screen will show the boot logo picture, then the new firmware revision number and

then the normal idle screen will show up. However, the standby LED will remain lit

yellow or magenta for another 10 seconds while executing an automatic self check.

During that time it may optionally, automatically reprogram the keypad processor - do

not power off at this stage! If the new software crashes during the time when the

standby LED was lit, or if the processor gets unplugged or if another upload is started

from the ethernet link by accidentally restarting the upload sequence (for example,

pressing browser "Reload/Refresh" button), the self check may fail which will force the

bootloader to reload the factory backup firmware on the next power up.

Firmware 2012.11 or later, do not automatically redefault the system configuration

parameters (in EEPROM memory) like the previous updates. This may potentially

cause a startup failure if some newly introduced parameters are not initialized, it also

depends on the old configuration status. This should not happen when upgrading from

05e but may happen with some older revisions prior to 05e. In such a case it is

recommended to upgrade first to revision 05e. Use:

ftp://bryston.com/pub/firmware/sp3/2012.05e/SP3.bin

The first time 2012.11 boots after upgrading from 05e, it will display a message on

screen:

EEPROM is incorrect!

Run MISCELLANEOUS->

DEFAULT EEPROM

Most frequent cause are: an incomplete file transfer due to network errors, breaking browser connection

by accidentally exiting it in the middle of a transfer, inadvertently refreshing browser upload page in the

middle of a transfer or immediately after the first new boot-up when the standby LED is still lit, or

accidental power down.

Содержание SP3









































































Результаты поиска

Содержание SP3

Отзывы:

Похожие инструкции для SP3

Бренды по названию

Популярные бренды

Bryston SP3, Руководство пользователя

Результаты поиска

Содержание SP3

Отзывы:

Похожие инструкции для SP3

Бренды по названию

Популярные бренды