Bruker BioSpec 117 AVANCE III Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 102

background image

58

ID: 182463115

Planning details

It is the responsibility of the system owner to decide on the usage of this feature and to realize
the connection between the BMU and the central alarm system of the building.

6.7

Cable lengths and routing

All connections between the cabinets in the technical room and the MR system in the magnet
room and/or in the operating area are made via the external cable set. The external cable set
contains electricity cables, lines for cryogenic gases, and refrigeration lines.
Detailed planning of cable lengths and compliance to these plans during the final installation is
a basic prerequisite for smooth installation of an MR system.

The relocation of the external line set is subject to specifications relating to:

▪

Compliance with the maximum cable lengths between components in the technical room
and the magnet cabinet (CCM) as well as the operating area.

▪

Compliance with the minimum bending radii of the different cables

▪

Cable routing with strain relief on cable trays at ceiling height

Cable routing with minimum distances is an advantage and should be strived for in every case.
The available RF power for MR signal excitation compared to the nominal output power of the
RF transmitter is reduced when long distances are used. Other than this, no further constraints
should be expected. The lengths of the cryogenic transfer line between the cryo-platform and
the MR CryoProbe™ has a strong influence on the signal to noise ratio of the CryoProbe and
must be minimized in every case by direct line routes. See chapter

Additional documents

Alarm type

Pin

Alarm states

Normally closed Pin 1 and 2 Contact closed in normal operating state, open during alarm
Normally open

Pin 3 and 4 Contact open in normal operating state, closed during alarm

The local project leader must immediately notify Bruker BioSpin MRI of any change to the cable
lengths required during the planning stage. Changes to construction of the installation, which
only become known during installation of the system, lead to enormous time delays.

«
...
56
57
58
59
60
...
»

Содержание BioSpec 117 AVANCE III







































































































Отзывы:

Нет отзывов

Похожие инструкции для BioSpec 117 AVANCE III

Бренд: Mainca Страницы: 21

Бренд: Daktronics Страницы: 30

Бренд: DAKOTA ULTRASONICS Страницы: 28

Бренд: Hach Страницы: 66

Бренд: Hach Страницы: 14

Бренд: Hach Страницы: 144

QuikChem 8500 2 Series

Бренд: Hach Страницы: 80

Бренд: Hach Страницы: 178

Бренд: Hach Страницы: 32

Бренд: hager Страницы: 4

Бренд: Ultraflex Страницы: 3

Бренд: Nellcor Страницы: 161

OXIMAX N-600X Series

Бренд: Nellcor Страницы: 210

Бренд: OAKWORKS Страницы: 24

Бренд: Olsen Страницы: 58

Бренд: Labnet Страницы: 12

Бренд: Zell Страницы: 32

Бренд: Uflex Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды