Brother HS-3000 Скачать руководство пользователя страница 147

Страница: 147 / 164

6 - 4

Repair Manual

Bad pattern shape

• Blocked by

satin pattern

• Fine BH

stitches

• Straight line

feed too small

• Stitches

uneven

Vertical rattle in feed dog

Back/front rattle
in feed dog

With the feed dog up,
check that there is no
rattle when the feed
dog is lightly moved
back and forth.

• Loose feed dog attachment

screw

Adjust feed dog attachment
screw

(4-18)

• Vertical rattle in feed bar

Reattach feed bar

(2-25)

(3-34)

Damage to horizontal feed cam

Replace lower shaft assy.

(2-29)

(3-26)

Rattle in feed adjuster

Reattach feed adjuster

(2-27)

(3-29)

Horizontal rattle in feed dog

Left-right rattle in
feed dog

With the feed dog up,
check that there is no
rattle when the feed
dog is lightly moved left
and right.

• Loose feed dog attachment

screw

Reattach feed dog

(2-24)

(3-35)

• Horizontal rattle in feed bar

Reattach feed bar

(2-25)

(3-34)

Bad feed dog height adjustment

Adjust feed dog height

(4-19)

Feed dog height

Refer to Feed dog
height.

(4-19)

Bad feed dog front-back position
adjustment

Adjust feed dog front-back
position

(4-18)

Feed dog front-
back position

Refer to Front/back and
left/right position of
feed dog.

(4-18)

Bad feed dog left-right position
adjustment

Adjust feed dog left-right
position

(4-18)

Feed dog left-
right position

Refer to Front/back and
left/right position of
feed dog.

(4-18)

Bad feed adjustment

Adjust feed

(4-14)

Feed

Refer to Forward/
backward feed.

(4-14)

Bad presser foot height and
parallel adjustment

Adjust presser bar height and
parallel

(4-13)

Presser foot
height and
parallelism

Refer to Presser bar
height and parallelism.

(4-13)

Problem

Primary factors and causes

Repair method

Items for

Inspection

Inspection method

and standards

Содержание HS-3000





































































































































































Результаты поиска

Содержание HS-3000

Отзывы:

Похожие инструкции для HS-3000

Бренды по названию

Популярные бренды

Brother HS-3000, Руководство по обслуживанию

Результаты поиска

Содержание HS-3000

Отзывы:

Похожие инструкции для HS-3000

Бренды по названию

Популярные бренды