Brother HS-3000 Скачать руководство пользователя страница 110

Страница: 110 / 164

4 - 9

Adjustment

Adjustment

Needle bar rising

1. Attach the front cover assy..

2. Remove the presser foot, the needle plate B and the needle plate A, and then remove the inner rotary hook.

3. Start the test mode.

4. Select the pattern number "02" (3-point needle drop mode).

5. Move the needle to the left with the

(Reverse stitch button), and then turn the power off.

6. Turn the pulley by hand and move the needle to its lowest position.

7. Remove the base cover.

8. Loosen the 2 socket set screws (CP, M5 x 5) on the lower shaft pulley D.

9. Turn the outer rotary hook by hand and adjust the right edge of the needle aligns with the outer rotary hook point

when raising up the needle bar 3.1 to 3.3mm from its lowest position.

10. Tighten the 2 socket set screws (CP, M5 x 5) on the lower shaft pulley D.

11. Attach the base cover.

Socket set screws

(CP, M5 x 5) (2pcs.)

Lower shaft pulley D

3.1 - 3.3mm

Base cover

The right edge of the needle aligns with the
outer rotary hook point when raising up the
needle bar 3.1 to 3.3mm from its lowest position.

Содержание HS-3000





































































































































































Результаты поиска

Содержание HS-3000

Отзывы:

Похожие инструкции для HS-3000

Бренды по названию

Популярные бренды

Brother HS-3000, Руководство по обслуживанию

Результаты поиска

Содержание HS-3000

Отзывы:

Похожие инструкции для HS-3000

Бренды по названию

Популярные бренды