Brother HL-960 Series Скачать руководство пользователя страница 81

Страница: 81 / 264

CHAPTER 4 CONTROL PANEL

4–13

Basic Operation Procedures

When you operate the MODE switch, remember the following basic
steps:

1. Press the SEL switch to set the printer off-line.

2. Press the MODE switch to enter the MODE menus.

The first mode menu appears on the display.

INTERFACE MODE

• Press the

▲

▼

switch to scroll through the menus forward or

backward. (Pressing the MODE switch allows forward scroll.)

INTERFACE MODE

←

▼

▲

→

FORMAT MODE

←

▼

▲

→

RESOLUTION MODE

←

▼

▲

→

…

• Press the SET switch to enter the next lower menu level of the

selected menu.

Mode Menu



SET

→

Setting Menu



SET

→

Sub-Setting Menu

• Press the

▲

▼

switch to select the setting on the display.

I/F=PARALLEL

←

▼

▲

→

I/F=RS-232C

←

▼

▲

→

…

• Press the SET switch to make the selected setting effective.
Then

you move to the next selection or exit to the upper menu level.

When you see “exit” and press the SET switch, you can exit
from the current level of menu to the next higher level of the
menu.

3. Advance to “exit MODE” and press the SET switch to exit from the

mode menus to the off-line ready state.

Pressing the SEL switch any time in any level of the menus allows
you to exit from the mode menus to the on-line state. The settings
you have made with the SET switch before exit are effective.

Содержание HL-960 Series









































































































































































































































































Результаты поиска

Содержание HL-960 Series

Отзывы:

Похожие инструкции для HL-960 Series

Бренды по названию

Популярные бренды

Brother HL-960 Series, Руководство пользователя

Результаты поиска

Содержание HL-960 Series

Отзывы:

Похожие инструкции для HL-960 Series

Бренды по названию

Популярные бренды