Brother HL-960 Series Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 264

background image

USER’S GUIDE

4–74

4. Press the SET switch to make the displayed selection effective.

The printer is reset according to the selected reset mode.

When the “RESET PRINTER” mode has been selected, the printer
is reset showing the message alternately as follows:

08 RESET TO

→

USER SETTINGS

When the “RESET SETTING 1-2” mode has been selected, the
printer is reset showing the message alternately as follows (#
indicates the selected number of saved settings):

08 RESET TO

→

SETTING #

When the “FACTORY SETTINGS” mode has been selected, the
printer is reset showing the message alternately as follows:

09 RESET TO

→

FACTORY SETTINGS

Then the printer automatically exits from the reset mode to the on-
line state.

List of Factory Settings

The following table shows the factory settings initially set before
shipment.

✒

Notes

•

The settings are subject to the emulation mode. Effective modes
are indicated in parentheses in the following table.

•

The following settings cannot be restored to the factory settings
with the RESET switch in the “FACTORY SETTINGS” mode:
INTERFACE MODE, HRC SETTING, PAGE PROTECTION,
SCALABLE FONT, LOCK PANEL, and PAGE COUNTER, and
local language for display messages.

•

The COPY setting is always restored to the factory setting when
the printer is turned off and on again.

•

The user settings are overwritten after resetting to setting 1 or 2.

«
...
140
141
142
143
144
...
»

Содержание HL-960 Series









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HL-960 Series

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 750

ImageCLASS 2300

Бренд: Canon Страницы: 8

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 750

Color imageCLASS 8180c

Бренд: Canon Страницы: 95

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 49

ImageCLASS 2300

Бренд: Canon Страницы: 156

Бренд: Canon Страницы: 193

Бренд: QMS Страницы: 24

imageCLASS D1120

Бренд: Canon Страницы: 36

ImageCLASS 2300

Бренд: Canon Страницы: 44

Бренд: Canon Страницы: 66

Бренд: 3D Systems Страницы: 26

Бренд: 3D Systems Страницы: 39

WorkSeries 200 Series

Бренд: 3D Platform Страницы: 9

Бренд: DataCard Страницы: 2

Бренд: FELIXprinters Страницы: 66

Бренд: JCM Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды