Brother HL-960 Series Скачать руководство пользователя страница 171

Страница: 171 / 264

CHAPTER 6 MAINTENANCE

6–7

Clean the printer interior as follows:

1. Turn off the printer and unplug the power cord.

2. Open the top cover of the printer and remove the toner cartridge.

3. Clean both sides of the paper access cover and transfer guide by wiping

off toner and paper particles with a dry, soft cloth. The paper access
cover can be lifted up to allow easier access for cleaning.

Fig. 6-6 Cleaning the Paper Access Cover

and Transfer Guide

4. Wipe off toner and paper particles from the top surface of the black

plastic paper guide with a dry, soft cloth.

Fig. 6-7 Cleaning the Paper Guide

5. Detach the cleaning brush from the top cover and clean the anti-static

teeth by sliding the brush several times. After cleaning, replace the
brush in its slot.

6. Refit the toner cartridge as described in REPLACING THE TONER

CARTRIDGE.

7. Close the top cover of the printer and plug in the power cord.

Paper Access Cover

Transfer Guide

Paper Guide

Содержание HL-960 Series









































































































































































































































































Результаты поиска

Содержание HL-960 Series

Отзывы:

Похожие инструкции для HL-960 Series

Бренды по названию

Популярные бренды

Brother HL-960 Series, Руководство пользователя

Результаты поиска

Содержание HL-960 Series

Отзывы:

Похожие инструкции для HL-960 Series

Бренды по названию

Популярные бренды