V
- 48
WSW35
(Function setting 13)
Selector
No.
Function
Setting and Specifications
1
|
4
Detection time length of the
disconnection tone in ICM
recording
No. 1
2 3 4
0
0 0 0 :
No detection
0
0 0 1 :
1 sec.
0
0 1 0 :
2 sec.
0
1 0 0 :
4 sec.
I I
1
1 1 1 :
15 sec.
5
|
8
Not used.
NOTE:
Selectors 1 through 4 are applicable to those models equipped with a built-in TAD.
l
Selectors 1 through 4:
Detection time length of the disconnection tone in ICM recording
If the equipment detects disconnection tone for the time length set by these selectors, it will
disconnect the line.
WSW36
(Function setting 14)
Selector
No.
Function
Setting and Specifications
1
|
5
Not used.
6
|
8
Lower limit of frequency to be
ignored after detection of calling
signals (Ci)
No. 6
7 8
0
0 0 :
0 (Not ignored)
0
0 1 :
4 (448 Hz)
0
1 0 :
8 (244 Hz)
0
1 1 :
12 (162 Hz)
1
0 0 :
16 (122 Hz)
1
0 1 :
20 (97 Hz)
1
1 0 :
24 (81 Hz)
1
1 1 :
28 (69 Hz)
l
Selectors 6 through 8:
Lower limit of frequency to be ignored after detection of calling signals (Ci)
At the start of reception, if the equipment detects the frequency of calling signals (Ci) specified by
selectors 1 through 4 of WSW14, it will start the ringer sounding. When doing so, the equipment
may fail to detect the calling signals normally due to noises superimposed at the time of reception.
To prevent it, use selectors 6 through 8 of WSW36.
If the equipment detects higher frequencies than the lower limit specified by these selectors, it will
regard them as noise and interpret that detecting state as being normal, allowing the ringer to keep
sounding (until the equipment starts automatic reception of FAX data if in the FAX mode or enters
the TAD mode if set in the TEL mode, according to the preset number of ringers).
Содержание FAX 750
