Broan GSEH3K Скачать руководство пользователя

Страница: 4 / 36

• Inspect the exterior of the unit for shipping damage. Ensure there is no damage to the door, door latches, main switch, etc.

1) Cardboard strip

• Inspect the interior of the unit for damage. Ensure the blower assembly, heat recovery core (model GSHH3K), energy recovery core

(model GSEH3K), insulation, dampers (models GSVH1K, GSHH3K and GSEH3K), prefilter, HEPA filter, etc. are all intact.

• If the unit was damaged during shipping, contact your local distributor, or Broan-NuTone at 1-800-558-1711.

1. BEFORE STARTING

1.1

NSPECT THE

ONTENTS OF THE

NOTE: Due to our ongoing commitment to product quality and innovation, all specifications are subjected to change without notice.

VD0126

CAUTION

Remove the cardboard strip inside the unit (if applicable).

WARNING

To avoid risk of suffocation, discard the plastic bag wrapping the unit.

2. TECHNICAL DATA

GSFH1K

GSVH1K

GSHH3K

GSEH3K

HEPA Filtration HEPA Filtration, HEPA Filtration,

Models

HEPA Filtration

& Fresh Air

Fresh Air & Fresh Air &

Ventilation

Heat Recovery Energy Recovery

Ventilation

Weight

34 lb (15.4 kg) 36 lb (16.3 kg) 40 lb (18.2 kg) 40 lb (18.2 kg)

Oval shaped duct collars
for non-insulated ducts

fits two 8” round ducts

to inside
Oval shaped duct collars
for insulated ducts

N/A

fits two 5” or 6” round ducts

to outside
Installation: Suspended

Chains, springs and hooks (provided with the unit)

or rest on a shelf or floor:

or 4 pads (provided with the unit)

Electrical Supply

120 Volts AC, 60 Hz

Power Consum. (Boost)

170 Watts

224 Watts

229 Watts

224 Watts

Power Consum. (Normal) 132 Watts

152 Watts

170 Watts

- 4 -

Содержание GSEH3K





































Результаты поиска

Содержание GSEH3K

Отзывы:

Похожие инструкции для GSEH3K

Бренды по названию

Популярные бренды

Broan GSEH3K, Руководство по установке

Результаты поиска

Содержание GSEH3K

Отзывы:

Похожие инструкции для GSEH3K

Бренды по названию

Популярные бренды