Broan GSEH3K Скачать руководство пользователя | Manualshive

Страница: 14 / 36

background image

- 14 -

6. INSTALL THE UNIT

6.1

T

OOLS AND

M

ATERIALS

Here are the tools and materials needed to perform the installation:

• Phillips screwdriver no. 2 or Robertson no. 1
• Hammer and flat blade screwdriver (for plenum connection installation only, to make holes in existing metal duct)
• Scissors or utility knife (to cut duct tape)
• Duct tape
• Tin snips or metal shear (for plenum connection installation only, to cut ductwork)
• Aluminum duct tape (for plenum connection installation only, use SMACNA duct tape)
• Jigsaw (except for the HEPA Filtration model GSFH1K)
• Extension cord
• Caulking gun and caulking (except for the HEPA Filtration model GSFH1K)
• 6’’ Diameter insulated ducting (except for the HEPA Filtration model GSFH1K)
• 8’’ Diameter insulated ducting.

NOTE: A 3-prong grounded 120 volt AC power outlet must exist or be installed within 3 ft of the unit, prior to unit installation.

6.2

M

OUNT THE

P

ORTS ON THE

U

NIT

Mount the 8” oval ports and the 5” to 6” oval ports on the top of the unit using the screws provided in
the hardware box (4 screws no. 8 x 3/4” long per port).

NOTES: 1. Although 4 screws are provided and prefered; only 1 screw per port is required to meet

code.

2. The HEPA Filtration only model has no 5” to 6” oval ports.

3. Do not install the front 8’’ oval port (item

1

in illustration) at this time.

VO0018

6.3

I

NSTALLATION

U

SING

I

SOLATOR

P

ADS

If the unit cannot be hung, use the four adhesive square isolation pads provided with the unit. According to your needs and model (with
or without drain), you can install the unit either in vertical or horizontal position.

CAUTION

When a HEPA Filtration Fresh Air & Heat Recovery Ventilation unit model GSHH3K is installed with adhesive isolator pads,
keep a minimum clearance of 4” between the unit and the ground (or shelf) for the drain.

1

CAUTION

Make sure the unit is level.

VD0074

V

ERTICAL POSITION

- A

LL MODELS

6.4

F

OR

S

USPENDED

A

PPLICATIONS

Use the four chains and springs in the hardware pack provided with the unit. According to your needs and model type, you can install the
unit either in a vertical or horizontal position.

H

ORIZONTAL POSITION

(

LEFT SIDE

)

A

LL MODELS

H

ORIZONTAL POSITION

(

RIGHT SIDE

)

M

ODEL

GSFH1K

ONLY

VD0075

VD0076

«
...
12
13
14
15
16
...
»

Содержание GSEH3K





































Отзывы:

Нет отзывов

Похожие инструкции для GSEH3K

Бренд: NEC Страницы: 15

Бренд: Zibro Страницы: 2

BoostIQ RoboVac 15C

Бренд: EUFY Страницы: 5

MLCA-MLHA-07-24 manua

Бренд: York Страницы: 22

VITALITY series

Бренд: York Страницы: 14

MTA8F128R5I Series

Бренд: Technibel Climatisation Страницы: 47

BULKHEAD BRE-026BS

Бренд: ActronAir Страницы: 24

Бренд: Danby Страницы: 12

Бренд: Zibro Страницы: 16

Бренд: ulsonix Страницы: 72

Бренд: Scarlett Страницы: 11

Бренд: MCS Master Страницы: 19

Бренд: Taurus Alpatec Страницы: 180

Бренд: Airwell Страницы: 20

Бренд: Vax Страницы: 20

Бренд: Daikin Страницы: 57

Бренд: nilco Страницы: 64

Бренд: Vax Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды