Broan GSEH3K Скачать руководство пользователя

Страница: 20 / 36

6. INSTALL THE UNIT

(CONT’D)

6.7 I

NSTALLING

™ E

XTERIOR

OOD

* (GSVH1K, GSHH3K

AND

GSEH3K

MODELS ONLY

)

(

CONT

’

)

6.7.2 L

OCATING THE

™ E

XTERIOR

OOD

The AirDuo™ exterior hood must be installed at a minimum distance of 18 inches (457 mm) above the
ground. See illustration beside.

6.7.3 C

ONNECTING

ANDEM

® T

RANSITION TO

™ E

XTERIOR

OOD

Using a jig saw, cut a 6’’ diameter hole in the exterior wall and insert the Tandem®
transition through this hole.

Joint the end of the Tandem® transition to the rear of the exterior backplate. Secure
with 2 Xmas tree pins and seal properly with duct tape.

VD00

8”

(457 mm)

WARNING

Make sure this hood is at least 6 feet (1.8 m) away (or more, as per applicable building codes or
standards) from sources of contamination such as:

• High efficiency furnace vent.

•Any exhaust from a combustion source.

• Gas meter exhaust, gas barbecue-grill.

•Garbage bin.

- 20 -

CAUTION

The exterior backplate must be installed with the word “TOP” pointing upward.

CAUTION

The Tandem® transition must be inserted in such a way that the

EXHAUST AIR TO OUTSIDE duct will be located on the top.

VD0084

VD0085

Xmas tree pin

EXHAUST AIR TO OUTSIDE duct

Using 4 no. 8 x 1½” screws, attach the exterior backplate to the exterior wall. Seal the
outline with caulking, as shown.

VD0086

VD0087

screw

Snap the assembled AirDuo™ exterior hood on its backplate and secure with two
provided screws (no. 8 x 3/4” long). Go to Section 6.9.

Содержание GSEH3K





































Результаты поиска

Содержание GSEH3K

Отзывы:

Похожие инструкции для GSEH3K

Бренды по названию

Популярные бренды

Broan GSEH3K, Руководство по установке

Результаты поиска

Содержание GSEH3K

Отзывы:

Похожие инструкции для GSEH3K

Бренды по названию

Популярные бренды