Broan GSEH3K страница 36 Скачать руководство пользователя | Manualshive

Страница: 36 / 36

background image

11.WARRANTY

WARRANTY

Broan-NuTone warrants to the original consumer purchaser of its products, that such products will be free from defects for a period of
two (2) years, from date of original purchase.

THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. BROAN-NUTONE WILL NOT BE HELD RESPONSIBLE FOR
ANY CLAIMS OVER THE ORIGINAL PURCHASE PRICE OF A

BROAN-NUTONE WHOLE-HOUSE AIR FILTRATION SYSTEM

,

NOR HELD RESPONSIBLE FOR SUBSEQUENT DAMAGE OR INCIDENT.

During the period stated above, Broan-NuTone will, at its opinion, repair or replace, without charge, any product or part which is found
to be defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO ANY FILTER, PREFILTER OR CORE FILTERS
(IF APPLICABLE). This warranty does not cover

a)

normal maintenance and service,

b)

any products or parts which have been subject

to misuse, negligence, accident, improper maintenance or repairs made by other than Broan-NuTone or

c)

a faulty installation or

installation contrary to recommended installation instructions.

The duration of any implied warranty is limited to the 2-year period as specified for the express warranty. Some states do not allow
limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE AT BROAN-NUTONE’S OPTION, SHALL BE THE PURCHASER'S
SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. This warranty supersedes
all prior warranties.

In order to qualify for a warranty claim, the owner of a Broan-NuTone WHOLE-HOUSE AIR FILTRATION SYSTEM must have the
model and serial number along with a proof of the original purchase date. In each case, costs for the removal of a defective part (and/or
unit) and installation of a new or repaired one and travel costs are not covered by this warranty.

BROAN-NUTONE LLC, 926 W. S STATE ST, HARTFORD WI 53027 1-800-637-1453

WHOLE-HOUSE AIR FILTRATION SYSTEM

99043105

- 36 -

«
...
34
35
36

Содержание GSEH3K





































Отзывы:

Нет отзывов

Похожие инструкции для GSEH3K

Бренд: Samsung Страницы: 23

Бренд: Samsung Страницы: 8

Бренд: Samsung Страницы: 12

Бренд: Daewoo Страницы: 30

Бренд: Samsung Страницы: 220

Бренд: Samsung Страницы: 240

Бренд: Samsung Страницы: 48

Бренд: Samsung Страницы: 200

Бренд: Samsung Страницы: 80

POWERbot SR10M70 Series

Бренд: Samsung Страницы: 16

POWERbot SR1 M70 Series

Бренд: Samsung Страницы: 184

POWERbot SR20K9000U Series

Бренд: Samsung Страницы: 26

Бренд: Samsung Страницы: 64

Бренд: Samsung Страницы: 16

Бренд: Samsung Страницы: 16

Бренд: Samsung Страницы: 16

Бренд: Samsung Страницы: 8

Бренд: Galletti Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды