Broan GSEH3K Скачать руководство пользователя

Страница: 30 / 36

7. CONTROLS

(CONT’D)

7.6

PERATING

ACCGSC1 C

ONTROLLER

7.6.1 ACCGSC1 C

ONTROLLER

ESCRIPTION

7.6.2 U

SING

ACCGSC1 C

ONTROLLER

• OFF: To stop the unit, slide the button on this position.
• L

: For a day-to-day usage, slide the button on this position.

The unit then will operate on low speed, providing 70 cfm.

• H

IGH

: For a high speed operation, slide the button on this position.

Generally used when more ventilation is required, such as parties, smokers, or for a 6-bedroom house.

This mode provides 105 cfm.

VC0059

High

Low

OFF

Reset Filter

Filter Maintenance

Power

OFF:

NIT IS OFF

OWER INDICATOR

LIGHTS UP

WHEN SLIDE SWITCH

IS ON

OW OR

IGH POSITION

ILTER MAINTENANCE

INDICATOR

FLASHES

EVERY MINUTE TO

INDICATE IT IS ON DUTY

FLASHES

EVERY SECOND WHEN

ITS TIME TO REPLACE

PREFILTER

. S

EMI

ANNUAL

AINTENANCE IN

ECTION

9.2.

LED STAYS LIT

WHEN ITS TIME TO

REPLACE FILTER AND PREFILTER

Low:

NIT IS OPERATING ON

LOW SPEED

ESET FILTER HOLE

NCE THE MAINTENANCE DONE

RESET THE FILTER

MAINTENANCE INDICATOR BY CAREFULLY INSERTING

A SMALL ROD

(

PAPER CLIP

)

IN THE

ESET

ILTER

HOLE

FOR

SECOND

. T

HE FILTER MAINTENANCE

INDICATOR WILL TURN OFF

. R

EFER TO THE

ILTER

AINTENANCE RECOMMENDATIONS IN

ECTION

IGH

NIT IS OPERATING ON

HIGH SPEED

- 30 -

7.7

PERATING

40425 C

ONTROLLER

7.7.1 ACCGSC3 C

ONTROLLER

ESCRIPTION

This wall controller is in OFF mode when power is applied for the first time. The mode does not change following a power failure.

VC009

LLUMINATES IN ALL MODES

EXCEPT

OFF

MODE

ILTER AND PREFILTER MAINTENANCE

LED.

LASHES

WHEN IT IS TIME TO REPLACE

PREFILTER AND WASH CORE FILTERS

IANNUAL

AINTENANCE IN

ECTION

9.1.

IGHTS UP

WHEN IT IS TIME TO REPLACE

FILTER AND PREFILTER AND WASH CORE FILTERS

NNUAL

AINTENANCE

ECTION

9.2.

RESS THIS BUTTON TO

ACCESS CONFIGURATION PARAMETERS

(

SEE

ECTION

7.7.3).

• P

RESS EITHER BUTTON TO CHANGE

CONFIGURATION SETTING

(

SEE SECTION

7.7.3).

• P

RESS BOTH BUTTONS TO RESET THE FILTER

COUNTER OR PREFILTER COUNTER

RESS THIS BUTTON TO

SWITCH MODE

(

SEE

ECTION

7.7.2).

Содержание GSEH3K





































Результаты поиска

Содержание GSEH3K

Отзывы:

Похожие инструкции для GSEH3K

Бренды по названию

Популярные бренды

Broan GSEH3K, Руководство по установке

Результаты поиска

Содержание GSEH3K

Отзывы:

Похожие инструкции для GSEH3K

Бренды по названию

Популярные бренды