BRIGHT OTF6000 Скачать руководство пользователя страница 55

Страница: 55 / 72

1. Cryo-M-Bed 53581 Product Information

Trade/Type:

Embedding Compound.

Container:

Disposable plastic bottles.

Uses:

Embedding compound for frozen tissue

specimens.

Description:

Colourless viscous liquid.

Cryo-M-Bed 53581

MATERIAL SAFETY DATA SHEET

Instruments

Office:

Bright Instruments LTD
Burnett House, Lakeview Court
Ermnie Business Park, Huntingdon
Cambridgeshire, PE29 6UA

Telephone: +44 (0) 808 168 9697
Email: [email protected]

Web: brightinstruments.com
Member:

2. Cryo-M-Bed 53581 Product Information

Information on Ingredients:

Blend of polyviol alcohol 217, thymol and water.

Physical and Chemical

Properties:

Colourless viscous liquid.

Stability and Reactivity:

May react with oxidising materials.

Toxicological Information:

No harmful eff ects if handled correctly. May give off toxic fumes in the case of fi re.

Ecological Information:

Degradable, miscible in all proportions.

Transport Information:

No restrictions.

Hazards Identifi cation:

Skin:

Can cause skin irritation.

Respiratory:

May cause diffi culty in breathing if exposed to very high concentration.

Ingest:

May be harmful by ingestion.

Eyes:

Can cause Eye irritation.

First Aid Procedures:

Skin:

Wash thoroughly, with soap and water.

Respiratory:

Move to fresh air.

Ingest:

Rinse mouth out with water, in sever cases seek medical attention.

Eyes:

Flush copiously for at least 15 minutes.

Fire Fighting Measures:

Hazards:

May cause toxic fumes.

Equipment:

Water spray, foam, dry powder, CO

Disposal Considerations:

Bag and dispose of waste in accordance with local authority requirements.

Handling Storage:

No special requirements.

Regulatory Information:

None.

Accidental Release Measures:

Absorb spillage on an inert absorbent, bag and arrange disposal. Wash area in

water and detergent.

Exposure Controls:

Skin:

Avoid contact.

Respiratory:

Avoid very high concentrations.

Ingest:

Do not eat, drink or smoke.

Eyes:

Goggles should be worn.

OES:

Not assigned (long term, 8 hour TWA).

Содержание OTF6000









































































Результаты поиска

Содержание OTF6000

Отзывы:

Бренды по названию

Популярные бренды

BRIGHT OTF6000, Руководство пользователя

Результаты поиска

Содержание OTF6000

Отзывы:

Бренды по названию

Популярные бренды