4. HOW TO INSTALL THE CHILD CAR SAFETY SEAT. GROUP 2 AND 3.
Use Group 2 and 3 only from approx.
4 to 12 years of age (15-36 kg)
WARNING
4.
Make sure the vehicle’s safety belt is not twisted, also check that
the seat cover does not impede the movement of the vehicle’s
safety belt or prevent the installation of the seat in any way. To
release your child unbuckle the vehicle safety belt as described in
the instructions.
When the seat is being used for group 1, the seat belt must pass
through the slot in the headrest and this should be in the lowest
position.
1.
Place the child seat on the seat of the vehicle, ensuring it is
pressed firmly against the back of the vehicle seat (4.1).
2.
Place the child in the child car safety seat (4.2).
3.
According to the child’s height the headrest can be adjusted up
or down. Place your hand on the headrest and press the lever
while pulling the seat down with the other hand so it does not
move (4.3).
4.
Pass the diagonal seat belt trough guide
B
located in the
headrest and the lap seat belt through guides
J
under both
armrests. Check that the seat belts are not twisted and tighten
by pulling the diagonal seat belt upwards (4.4, 4.5, 4.6 and 4.7).
5.
Attach the seat belt to the vehicle anchor point and press until
you hear a “
click
” that lets you know that the child seat is properly
installed (4.8).
6.
Make sure the vehicle’s safety belt is not twisted, also check that
the seat cover does not impede the movement of the vehicle seat
belt or prevent the installation of the seat in any way. To release
your child unbuckle the vehicle safety belt as described in the
instructions.
Ensure that the belt is well tightened.
Before installing the seat it is necessary to remove harness straps,
crotch straps and lap straps as shown in Chapter 6.
5. ADJUST THE HARNESS TO THE HEIGHT OF THE CHILD.
Changing the harness height
1.
Adjust the height of the harness, by pressing the harness
adjustment button and pulling the harness straps towards you to
loosen them (5.2).
2.
Place your hand on the headrest and press the lever
M
while
pulling the seat down with the other hand so it does not move
(5.3).
3.
Then unhook one of the harness connector straps at the back
of the seat and pull the loose strap towards the front of the seat
(5.4).
4.
Insert the harness strap into the
O
slot of the fabric and backrest
at the front of the seat. Then insert the harness strap into the
appropriate upper or lower slot at the rear of the seat (5.5).
5.
Reinsert the harness strap in the harness connector on the back
of the seat (5.6).
6.
Then, do the same with the other harness strap. Verify that the 2
harness straps go through the slots at the same height. Do not
use the upper guides of the child seat. These should only be used
to guide the vehicle’s safety belts.
Fastening the harness
1.
Join the 2 buckle metal connectors (5.7).
2.
Pass both connectors through the slot in the upper part of the
buckle until you hear a “
click
” (5.8).
3.
Always make sure the harness is properly fastened by pulling the
harness straps upwards (5.9).
4.
To unfasten the harness press the red button on the buckle
downwards (5.10).
Always check that the harness straps are suitable for the height of
your child. The shoulders of the child should always be just below
the back slots at a suitable height (5.1).
22
23
www.babyqs.com
BEZ123
Child restraint system
Group 1/2/3
EN
Содержание AB730
Страница 3: ...4 5 www babyqs com BEZ123 A D E F G I C N P Q R O M J H B K 1 2 3 4 3 1 B I I 3 2 3 6 3 5 L B I I 3 3...
Страница 4: ...6 7 www babyqs com BEZ123 4 1 4 5 4 6 4 3 4 4 4 7 4 8 4 2 J B J J J B 5 1 A B C 5 3 5 4 5 2...
Страница 5: ...8 9 www babyqs com BEZ123 5 8 5 10 5 11 5 12 5 7 5 5 5 6 5 9 6 1 6 4 6 2 6 3...
