Boston Scientific Swiss LithoCast Trilogy FT-235 Скачать руководство пользователя страница 47

Страница: 47 / 48

IC Statements:

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following

two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Under Industry Canada regulations, the radio transmitter(s) in this device may only operate using an antenna of a

type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio inter-

ference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated

power (e.i.r.p.) is not more than that necessary for successful communication.

Содержание Swiss LithoCast Trilogy FT-235

















































Результаты поиска

Содержание Swiss LithoCast Trilogy FT-235

Отзывы:

Похожие инструкции для Swiss LithoCast Trilogy FT-235

Бренды по названию

Популярные бренды

Boston Scientific Swiss LithoCast Trilogy FT-235, Инструкция по эксплуатации

Результаты поиска

Содержание Swiss LithoCast Trilogy FT-235

Отзывы:

Похожие инструкции для Swiss LithoCast Trilogy FT-235

Бренды по названию

Популярные бренды