Bosch VideoJet 8004 Скачать руководство пользователя страница 85

Страница: 85 / 164

VideoJet 8008 / VideoJet 8004

| Installation and Operating Manual

| 85

Bosch Security Systems | 2006-07 | V1.5

Configuration using a Web browser

Caution

All modifications to settings are only effective if you complete the configu-
ration in the last window of the wizard by clicking

Finish

– Switch to the last window of the wizard if necessary.

– Click

Finish

to complete the configuration. All settings are now transferred to

the unit and subsequently become effective.

Editing a partition

You can modify the configuration of a partition at any time.

Caution

All modifications result in the reorganization of the partition and the loss of
all sequences on this partition.

Changes to the size of a partition (

Partition total size

) lead to the entire

hard drive being reorganized and the loss of all sequences stored on the
drive.

Содержание VideoJet 8004





































































































































































Результаты поиска

Содержание VideoJet 8004

Отзывы:

Bosch VideoJet 8004, Инструкция по установке и эксплуатации, Страница: 85 / 164

Результаты поиска

Содержание VideoJet 8004

Отзывы: