Bosch VideoJet 8004 Скачать руководство пользователя страница 7

Страница: 7 / 164

VideoJet 8008 / VideoJet 8004

| Installation and Operating Manual

| 7

Bosch Security Systems | 2006-07 | V1.5

Safety information

Safety information

Electric shock hazard

❚

Never attempt to connect the unit to any power network other than the type
for which it is intended.

❚

Never open the housing.

❚

If a fault occurs, disconnect the unit from the power supply and from all other
units.

❚

Install the unit only in dry, weather-protected locations.

❚

If safe operation of the unit cannot be ensured, remove it from service and
secure it to prevent unauthorized operation. Safe operation is no longer pos-
sible in the following cases:

– if there is visible damage to the unit or power cables,

– if the unit no longer operates correctly,

– if the unit has been exposed to rain or moisture,

– if foreign bodies have penetrated the unit,

– after long storage under adverse conditions, or

– after exposure to extreme stress in transit.

In such cases, have the unit checked by Bosch Security Systems.

Содержание VideoJet 8004





































































































































































Результаты поиска

Содержание VideoJet 8004

Отзывы:

Bosch VideoJet 8004, Инструкция по установке и эксплуатации, Страница: 7 / 164

Результаты поиска

Содержание VideoJet 8004

Отзывы: