Bosch VideoJet 8004 Скачать руководство пользователя страница 71

Страница: 71 / 164

VideoJet 8008 / VideoJet 8004

| Installation and Operating Manual

| 71

Bosch Security Systems | 2006-07 | V1.5

Configuration using a Web browser

Picture settings

You can set the video image of each camera to suit your requirements. The cur-
rent video image is displayed in the small window next to the slide controls as
confirmation. Your changes are effective immediately.

– Click a tab to select the corresponding camera.

– Set the slide bar to the desired position.

– Click

Default

to reset all settings to their default value.

Contrast (0...255):

You can use this function to adapt the contrast of the video image to your work-
ing environment.

Saturation (0...255):

You can use this function to adjust the color saturation so as to make the repro-
duction of colors on your monitor as realistic as possible.

Brightness (0...255):

You can use this function to adapt the brightness of the video image to your
working environment.

Содержание VideoJet 8004





































































































































































Результаты поиска

Содержание VideoJet 8004

Отзывы:

Bosch VideoJet 8004, Инструкция по установке и эксплуатации, Страница: 71 / 164

Результаты поиска

Содержание VideoJet 8004

Отзывы: