Bosch VideoJet 8004 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 164

Bosch VideoJet 8004 Скачать руководство пользователя страница 17

VideoJet 8008 / VideoJet 8004

| Installation and Operating Manual

EN

| 17

Bosch Security Systems | 2006-07 | V1.5

Installation

Installation

4

VideoJet 8008 and VideoJet 8004 are designed as desktop units and intended
for installation in a switch cabinet. Mounting in a 19-inch rack using the mounting
kit supplied is a quick and easy operation.

For desktop operation, four self-adhesive, non-slip rubber feet are included,
which you can stick to the bottom of the unit.

Caution

The unit is designed for indoor operation. Select a suitable location for in-
stallation where the unit will not be subjected to conditions of extreme tem-
perature or humidity. The ambient temperature must be between 0 and
+40 °C (+32 and +104 °F), and the relative humidity must not exceed 80%
(non-condensing).

The unit heats up during operation, so you should ensure that there is ad-
equate ventilation and enough clearance between the unit and heat-sen-
sitive objects or equipment.

Please ensure the following installation conditions:

❚

Do not install the unit close to heaters or other heat sources. Avoid locations
exposed to direct sunlight.

❚

Allow sufficient space for running cables.

❚

Ensure that the unit has adequate ventilation. Bear the total heat output in
mind, particularly when installing multiple units in a switch cabinet.

❚

When making connections, use only the cables supplied or use appropriate
cables immune to electromagnetic interference.

❚

Position and run all cables so that they are protected from damage, and pro-
vide adequate cable strain relief where needed.

❚

Avoid impacts, blows and severe vibrations as these can irreparably damage
the unit.

«
...
15
16
17
18
19
...
»

Содержание VideoJet 8004





































































































































































Отзывы:

Нет отзывов