Bosch VideoJet 8004 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 164

Bosch VideoJet 8004 Скачать руководство пользователя страница 20

Installation and Operating Manual |

VideoJet 8008 / VideoJet 8004

EN

| 20

Installation

Bosch Security Systems | 2006-07 | V1.5

Connections

Cameras

You can connect a maximum of eight standard video sources (such as CCTV
cameras). Any cameras and other video sources that produce a standard PAL
or NTSC signal are suitable.

Note

On the VideoJet 8008, the maximum resolution at the complete image rate
for each camera input is Full D1/4CIF. The VideoJet 8004 only supports
the Full D1/4CIF resolution when every other camera input is assigned,
that is, when the four uneven inputs (

Video 1

,

3

,

5

,

7

) or the four even in-

puts (

Video 2

,

4

,

6

,

8

) are assigned. If all eight inputs are assigned, the

VideoJet 8004 supports a maximum resolution of 2CIF at the full image
rate. Mixed assignment is also possible: for example, assign

Video 1

to

Video 4

(2CIF) and then only

Video 5

and

Video 7

(4CIF each).

– Connect the cameras or other video sources with a video cable

(75 Ohm, BNC plug) to the BNC

Video 1

to

Video 8

sockets.

– Set the

75

Ω

sliding switch under the BNC sockets to

●

, in order to terminate

the video input, if the video signal is not looped through.

VideoJet 8008

Video 1 Video 2 Video 3 Video 4 Video 5 Video 6 Video 7 Video 8

4CIF

4CIF

4CIF

4CIF

4CIF

4CIF

4CIF

4CIF

VideoJet 8004

Video 1 Video 2 Video 3 Video 4 Video 5 Video 6 Video 7 Video 8

4CIF

—

4CIF

—

4CIF

—

4CIF

—

—

4CIF

—

4CIF

—

4CIF

—

4CIF

2CIF

2CIF

2CIF

2CIF

2CIF

2CIF

2CIF

2CIF

2CIF

2CIF

2CIF

2CIF

4CIF

—

4CIF

—

«
...
18
19
20
21
22
...
»

Содержание VideoJet 8004





































































































































































Отзывы:

Нет отзывов