Bosch rexroth MS2N03-A Скачать руководство пользователя страница 20

Страница: 20 / 72

20 / 72

MS2N

Features and functions

Bosch Rexroth AG

R911347581, Edition 05

The occurring electro-chemical processes within

the cooling system must be minimized via selec-

tion of the materials. Do not combine different

materials, like copper, brass, iron, zinc and halo-

genated plastics (e.g. tubes and sealing made of

PVC).
Fix coolant ducts and check for their tightness in

regular intervals.

Potential equalization

Connect all components within the cooling

system (e.g. motor, heat exchanger, pipe system,

pump, pressure compensation container, etc.)

with a potential equalization. Do the potential

equalization with a copper bus bar or copper wire

with an appropriate conductor cross-section.
Coolant ducts must not contact live parts. Please

observe sufficient insulation according to the reg-

ulations valid for the place of installation.

Cleaning the coolant circuit

Inspect and clean (purge) the cooling system

at regular intervals as specified in the machine

and cooling system manufacturer's maintenance

schedule.
Note that the utilization of unsuitable cleaning

agents may cause irreversible damage to the

motor cooling system. This type of damage does

not lie within the responsibility of Bosch Rexroth.

NOTICE

Damage to the motor cooling system due to

unsuitable cleaning agents!

−

The only liquids or materials allowed to

be used for cleaning and motor cooling

are those which do not corrode the motor

cooling system or do not react aggressively

to the materials used in Bosch Rexroth

motors.

−

Observe the instructions of the manufac-

turers of the cleaning agent and the cooling

system.

Coolants

The coolant must comply with certain criteria

and treated accordingly

⮫

Table on page 20

). To

ensure corrosion protection and chemical stabili-

zation admix an additive to the cooling water. The

selected coolant additives (biocides, inhibitors)

must comply with the materials in the cooling

system (e.g. copper, brass, stainless steel, etc.)

and minimize the micro-biological growth. Pay

attention to environmentally friendly materials.
A cooling with floating water from the supply

network is not allowed. Floating water can cause

sediments (chalk) or corrosion within the cooling

system.

Remark:

In the case of other used coolants

than water (e.g. oil), a performance reduction

of the motor can be necessary to dissipate the

created power loss.

NOTICE

Motor damage due to missing or incompatible

coolant water!

−

For this reason, water cooled motors may

only be operated as long as coolant supply

is ensured.

−

Do not use any cooling lubricants or cut-

ting materials from machining processes for

cooling.

−

Using aggressive coolant additives or addi-

tives can lead to irreparable motor damage.

Remark:

The dimensioning of the cooling

system is in the responsibility of the machine

manufacturer.
Adjust the required coolant, especially the mate-

rial compatibility must be specified with the man-

ufacturer of the cooling unit and the manufac-

turer of the coolant additives. The basic minimum

requirements for the coolant are displayed in the

following.

Cooling water quality for motors with internal cooling circuit

made of stainless steel.

pH value (bei 20 °C)

6 ... 9

Total hardness

1.2 ... 2.5 mmol/l

Содержание rexroth MS2N03-A









































































Результаты поиска

Содержание rexroth MS2N03-A

Отзывы:

Похожие инструкции для rexroth MS2N03-A

Бренды по названию

Популярные бренды

Bosch rexroth MS2N03-A, Руководство по эксплуатации

Результаты поиска

Содержание rexroth MS2N03-A

Отзывы:

Похожие инструкции для rexroth MS2N03-A

Бренды по названию

Популярные бренды