Bosch rexroth MS2N03-A Скачать руководство пользователя страница 58

Страница: 58 / 72

58 / 72

MS2N

Derating in case of deviating ambient conditions

Bosch Rexroth AG

R911347581, Edition 05

A permanent use of the motors is possible when

the specified class 3K22 according to EN IEC

60721-3-3:2019 is observed. Deviations and

enhancements according to the follwing table

must be observed.
Table 13: Ambient conditions

Operation

Installation altitude

0 … 1,000 m above MSL

Ambient temperature

0 … +40 °C

Relative humidity

5 … 95

Absolute humidity

1 … 29

g/m

8.3.1

Vibration load during opera-

tion

Vibrations are sine-wave oscillations in stationary

use, which vary in their effect on the resistance of

the motors depending on their intensity.
The specified limit values are valid for frequen-

cies of 10‑2000

Hz during stimulation on the

motor flange. Limitations can be necessary for

occurring resonances depending on the applica-

tion and installation situation.
The following limit values apply according to

60068-2-6 for MS2N motors:

Fig. 33: Vibration load on measuring points
Table 14: Permissible vibration load for MS2N

motors

Measuring point, direc-

tion

Limit value (10-2000

Hz)

Motors
Self-

cooling

Motors
Forced

ventilation

Motors
Water

cooling

1, 2 (radial motor

flange)

30 m/s²

10 m/s²

4, 5 (radial bearing

shield / fan)

50 m/s²

25 m/s²

3 (axial motor flange) 10 m/s²

10 m/s²

6 (axial bearing shield /

fan)

25 m/s²

Check the vibration load on the fan housing in

case of forced ventilation. The specified values

must not be exceeded.

8.4

Operation

During operation, keep the ambient and opera-

tion conditions and technical data specified in

the project planning manual.

Checks during operation:

•

Pay attention to exceptional noise.

•

Pay attention to increased vibrations.

•

Check the motors and fan units for cleanli-

ness.

•

Check the tightness of the coolant connec-

tions.

•

Check the monitoring devices and diag-

nostic / error messages of the controllers.

Decommission the drive when deviations from

normal operation exist. For further procedure

refer to .

8.5

Derating in case of devi-

ating ambient conditions

Reduce high performance data:

Reduce the standstill torque M

60K

100K

specified in the data sheet, with

the following factors.
We have:
M

0 red

= M

0 60K

× f

TH 60K

0 red

= M

0 100K

× f

TH 100K

0 red

= M

0 100K

× f

TH W

Содержание rexroth MS2N03-A









































































Результаты поиска

Содержание rexroth MS2N03-A

Отзывы:

Похожие инструкции для rexroth MS2N03-A

Бренды по названию

Популярные бренды

Bosch rexroth MS2N03-A, Руководство по эксплуатации

Результаты поиска

Содержание rexroth MS2N03-A

Отзывы:

Похожие инструкции для rexroth MS2N03-A

Бренды по названию

Популярные бренды