Bosch rexroth CytroForce-M Скачать руководство пользователя страница 43

Страница: 43 / 85

43 / 85

Servo-hydraulic actuator

Mounting the servo-hydraulic actuator

Bosch Rexroth AG

RE62270-B, 01.21

Fig. 9: Cable installation
1 Signal and control cables in the same cable duct

2 Power cables in the same cable duct

3 Common installation in one cable duct, separated by a metal partition wall

●

If signal lines and power cables cross, install them at an angle of 90° to pre-

vent interference coupling.

Fig. 10: Installation with 90-degree offset

●

Earth unused and unconnected spare cables at both ends to prevent them

from having an antenna effect.

●

Avoid unnecessary line lengths and shorten the cables.

●

If possible, install cables as close as possible to grounded metal surfaces

(reference potential). Grounded and closed cable channels or metal pipes

are the ideal solution.

●

Avoid freely suspended lines and lines installed on plastic supports. They act

as receiving antennas (immunity to interference) and also as transmitting

antennas (interference radiation).

Shielding

●

Connect the cable shield with a short cable length directly to the devices

and ground it over a large surface area.

●

Connect the shield of analog signal cables over a large surface area on one

end, usually in the control cabinet. Ensure an short connection over a large

area to the ground / housing.

Содержание rexroth CytroForce-M






















































































Результаты поиска

Содержание rexroth CytroForce-M

Отзывы:

Похожие инструкции для rexroth CytroForce-M

Бренды по названию

Популярные бренды

Bosch rexroth CytroForce-M, Руководство по эксплуатации

Результаты поиска

Содержание rexroth CytroForce-M

Отзывы:

Похожие инструкции для rexroth CytroForce-M

Бренды по названию

Популярные бренды