Bosch rexroth CytroForce-M Скачать руководство пользователя страница 14

Страница: 14 / 85

14 / 85

Servo-hydraulic actuator
Product-specific safety instructions

Bosch Rexroth AG

RE62270-B, 01.21

WARNING

High voltage above 50 V! Danger to life and risk of injury

caused by electric shock.

−

De-energize the servo-hydraulic actuator before instal-

lation, pulling and connecting connectors and all

other work.

−

Secure the electrical equipment against restarting.

Use inspected measuring equipment to verify that

there is no voltage applied.

−

Before switching the control system on, check the

protective conductor on all electrical devices for

proper connection according to the wiring diagram.

−

Measure the electric voltage of electrical parts before

beginning work in order to avoid hazards caused by

contact.

−

After switching off, wait until the capacitors have dis-

charged below the permissible voltage of 50 V. The

components of the drive system Rexroth IndraDrive

are dimensioned so that after the supply voltage was

turned off, the voltage falls below 50 V within the dis-

charge time of max. 30 minutes.

−

Never touch electrical connection points of the com-

ponents while power is turned on.

WARNING

Danger due to hydraulic fluid under pressure! Danger of

poisoning and risk of injury (e.g. eye injuries, skin

lesions, poisoning due to inhalation and ingestion).

−

Check the lines for wear and damage before any com-

missioning.

−

Use personal protective equipment (e.g. safety gog-

gles, protective gloves, suitable workwear, safety

shoes, etc.)

−

If nevertheless hydraulic fluid comes into contact with

the eyes or penetrates the skin, please consult a

doctor immediately.

−

When handling hydraulic fluids, strictly observe the

safety notes of the hydraulic fluid manufacturer.

WARNING

Hot surfaces! Risk of burning. The servo-hydraulic

actuator heats up considerably during operation. Indi-

vidual components of the servo-hydraulic actuator can

get so hot during operation that you may burn yourself.

−

Let the servo-hydraulic actuator cool down before

touching it.

−

Protect yourself by wearing heat-resistant protective

clothing, e.g. gloves.

WARNING

Combustible hydraulic fluid! Risk of fire.

−

Keep open fire and ignition sources away from the

servo-hydraulic actuator.

−

Ensure sufficient ventilation.

−

Do not carry out welding work on or in the vicinity of

servo-hydraulic actuator.

Содержание rexroth CytroForce-M






















































































Результаты поиска

Содержание rexroth CytroForce-M

Отзывы:

Похожие инструкции для rexroth CytroForce-M

Бренды по названию

Популярные бренды

Bosch rexroth CytroForce-M, Руководство по эксплуатации

Результаты поиска

Содержание rexroth CytroForce-M

Отзывы:

Похожие инструкции для rexroth CytroForce-M

Бренды по названию

Популярные бренды