Bosch Rexroth CS 440RC Скачать руководство пользователя страница 54

Страница: 54 / 57

54/57

Bosch Rexroth Canada ı 03.10.2011 ı Revision 5.4

cursor should show up under one digit), scroll Up/Down on the keypad to

adjust valve output to the Min or Max speed, and ENTER to save settings.

•

For Wt/Area (g/m*m) operation a feedback sensor is required. Select -

>PROGRAM MODE->SENSORS & VALVES->SPINNER SETUP->AUTO NULL, Press

ENTER to select, and ENTER again to start. Once AUTO NULL stops it

completes. Also a width calibration is required. From the SPINNER SETUP menu

select WIDTH CALIBRATION. On the screen you need to put in the spreading

width at 0 rpm (typically the diameter of the spinner), and then select

CONVEYOR knob to start the conveyor. Gradually increase the spinner setting to

the maximum spreading width required, measure the width, turn all knobs to

off, key in measured spreading width in mm, and then select ACCEPT VALUE.

16.

How to set up or null min/max outputs of a Prewet/Liquid pump?

•

For MANUAL operation, select MANUAL MODE on SYSTEM SETUP->PREWET

MODE menu screen, then select Min Out or Max Out, press ENTER to go into

edit mode (an cursor should show up under one digit), Press Up/Down on the

keypad to control the flow of the pump to the desired Min or Max flow rates,

press ENTER to store the value and exit edit mode.

•

For CLOSED LOOP operation, either pulses/rev or flow/min, ->PROGRAM

MODE->SENSORS & VALVES->CONVEYOR SETUP->VALVE SETTINGS, ensure

that correct pulses are put in, Select AUTO NULL, Press ENTER to select, and

ENTER again to start. Once AUTO NULL stops it completes.

Note: For very slow conveyors (max RPM < 100) the AUTO NULL may start twice to

calculate correct max RPM value.

17.

Why does conveyor valve auto

Why does conveyor valve auto----null run twice with some trucks?

null run twice with some trucks?

The max RPM for a typical conveyor motor is over 250, and the CS-440RC

controllers set parameter ranges to accommodate that. In cases of max conveyor

RPM less than 250 the CS-440RC controllers would detect the low conveyor RPM on

the first null attempt to adjust RPM range, and then determine the Min and Max the

second time.

18.

How does Fwd Gain work?

“Forward Gain” is designed to help conveyor overcome the inherited hydraulic

motor pulsing problem by boosting the conveyor valve output when vehicle starts to

move. Once the hydraulic motor inlet oil pressure is sufficient to create motion, the

motor will pulse during start up until it receives enough oil flow for continuous

motion. Forward Gain is only temporary and it will disappear once the conveyor is

turning. The feature is very helpful to eliminate conveyor pulsing at start up.

Содержание Rexroth CS 440RC


























































Результаты поиска

Содержание Rexroth CS 440RC

Отзывы:

Похожие инструкции для Rexroth CS 440RC

Бренды по названию

Популярные бренды

Bosch Rexroth CS 440RC, Подробное руководство по настройке и конфигурации

Результаты поиска

Содержание Rexroth CS 440RC

Отзывы:

Похожие инструкции для Rexroth CS 440RC

Бренды по названию

Популярные бренды