Bosch Rexroth CS 440RC Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 57

background image

21/57

Bosch Rexroth Canada ı 03.10.2011 ı Revision 5.4

Start the truck and operate the engine at 1500 RPM to ensure good hydraulic oil

flow.

Press the Enter button and using the Navigational arrow move the cursor under the

last digit.

Using the Up navigational arrow increase the output until the conveyor starts to turn

(see RPM reading in lower corner).

Using the Down navigational arrow, slowly decrease the output in small increments

until the conveyor stops.

The reading on the screen for “Min Out” is the % of maximum amperage required to

start the conveyor.

Press the Enter button to return the cursor in front of the Min reading.

5.1.2 Maximum Nulling

Using the Down navigational arrow move the cursor in front of “Max Out”. Press the

Enter button and using the navigational arrow move the cursor under the last digit.

The conveyor should now be turning and the RPM reading should show in the lower

corner.

Using the Up or Down navigational arrows, adjust the RPM to the maximum

hydraulic motor design RPM. If the hydraulic motor specs are not available, slowly

increase the speed until there are no further increases in the RPM reading. Now

slowly lower the output until the RPM reading just starts to go down.

The reading on the screen is % of maximum controller output allowed, permitting

the conveyor motor to operate only to its maximum speed.

Press the Enter button to return the cursor in front of the Max reading. Press the

Escape button once to return to the previous screen.

5.1.3 Auto Nulling

The nulling of the solenoids for minimum and maximum speed can also be

accomplished automatically.

Move the cursor in front of “AUTO NULLING”, press the Enter button, and the

screen to the left will appear.

«
...
19
20
21
22
23
...
»

Содержание Rexroth CS 440RC


























































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth CS 440RC

Бренд: Fairchild Страницы: 2

Бренд: Fagor Страницы: 103

Бренд: YASKAWA Страницы: 256

Бренд: Jabra Страницы: 8

Бренд: Zeta Страницы: 44

Extra Free RZB-02

Бренд: Zamel Страницы: 2

Бренд: Yamaha Страницы: 2

Бренд: Sunnen Страницы: 24

CentriPro Aquavar SOLO

Бренд: Xylem Страницы: 48

infi 90 IMMFP12

Бренд: Bailey Страницы: 75

iSteam 2.0 Control

Бренд: mr. steam Страницы: 16

Бренд: Sygonix Страницы: 12

Бренд: Case IH Страницы: 81

Бренд: J+J Страницы: 6

Бренд: Water Worker Страницы: 8

Бренд: YASKAWA Страницы: 360

Бренд: W.E.S.T. Elektronik Страницы: 53

Бренд: Kelly Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды