Bosch Rexroth 10 Series Скачать руководство пользователя страница 7

Страница: 7 / 72

RE 91485-01-B/2021-11-18, Bosch Rexroth AG

About this documentation |

A10FZO/G, A10VZO/G

/72

Tabelle 3: Meaning of symbols

Symbol

Meaning

If this information is disregarded, the product cannot be used and/or
operated to its full extent.

▶

Single, independent action

1�
2�
3�

Numbered instruction:
The numbers indicate that the actions must be completed in order.

1�3�3 Designations

This documentation uses the following designations:

Tabelle 4: Designations

Designation

Meaning

A10FZO

Axial piston fixed displacement unit, open circuit

A10VZO

Axial piston variable displacement unit, open circuit

A10FZG

Axial piston fixed displacement unit, open and closed circuit

A10VZG

Axial piston variable displacement unit, open and closed circuit

Threaded plug

Metal screw, pressure-resistant

Protective plug

Made out of plastic, not pressure-resistant, only for transportation

As a generic term for "axial piston units for variable-speed drives
A10FZO, A10VZO, A10FZG and A10VZG", the designation "axial piston unit" will be
used hereinafter.

1�3�4 Abbreviations

This documentation uses the following abbreviations:

Tabelle 5: Abbreviations

Abbreviation

Meaning

ANSI

merican

ational

tandards

nstitute is an organization that coordinates

the development of voluntary standards in the United States

ATEX

EC directive on explosion protection (

mosphère

plosible)

DIN

eutsches

nstitut für

ormung (German Institute for Standardization)

Two-point control,

irectly

ontrolled

ruck

egler (pressure controller), hydraulic

wo point control

lectric

ISO

nternational

rganization for

tandardization

JIS

apan

ndustrial

tandard

Torque controller

exroth document in the

nglish language

VDI 2230

Guideline for the systematic calculation of heavy-duty
threaded connections and cylindrical screw joints from the
VDI (

erein

eutscher

ngenieure - Association of German Engineers)

Содержание Rexroth 10 Series









































































Результаты поиска

Содержание Rexroth 10 Series

Отзывы:

Похожие инструкции для Rexroth 10 Series

Бренды по названию

Популярные бренды

Bosch Rexroth 10 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Rexroth 10 Series

Отзывы:

Похожие инструкции для Rexroth 10 Series

Бренды по названию

Популярные бренды