Bosch Rexroth 10 Series Скачать руководство пользователя

Страница: 14 / 72

Bosch Rexroth AG, RE 91485-01-B/2021-11-18

/72

A10FZO, A10VZO, A10FZG and A10VZG series 10

| Safety instructions

CAUTION

Contact with hydraulic fluid!

Risk of adverse health effects, e.g. eye injury, skin irritation, toxication from
inhalation!

▶ Avoid any contact with hydraulic fluids.

▶ When handling hydraulic fluids, the safety instructions of the lubricant

manufacturer need to be observed at all times.

▶ Use your personal protective equipment (e.g. safety goggles, safety gloves,

suitable working clothes, safety shoes).

▶ Immediately seek medical attention, however, if hydraulic fluid gets into your

eyes or blood circuit or if you swallow it accidentally.

Danger from improper handling!

Slip hazard! Risk of slipping on wet surfaces when climbing on the axial piston
unit.

▶ Never grab or climb onto the axial piston unit.

▶ Check how to safely get on top of the machine/system.

2�7 Personal protective equipment

Personal protective equipment is the responsibility of the user of the axial piston
unit. Observe the safety regulations in your country.
All pieces of personal protective equipment should be intact.

Содержание Rexroth 10 Series









































































Результаты поиска

Содержание Rexroth 10 Series

Отзывы:

Похожие инструкции для Rexroth 10 Series

Бренды по названию

Популярные бренды

Bosch Rexroth 10 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Rexroth 10 Series

Отзывы:

Похожие инструкции для Rexroth 10 Series

Бренды по названию

Популярные бренды