Bosch Rexroth 10 Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 72

background image

RE 91485-01-B/2021-11-18, Bosch Rexroth AG

Safety instructions |

A10FZO/G, A10VZO/G

11

/72

2�6 Product-specific safety instructions

The following safety instructions apply to chapters 6 to 14.

WARNING

Danger due to excessive pressure!

Risk of death or injury, or property damage!
Improperly changing the factory pressure settings can result in a pressure
increase beyond the permissible maximum pressure.
Operating the unit above the maximum permissible pressure can cause
components to burst and hydraulic fluid to escape under high pressure.

▶ Changes to the factory settings may only be made by Bosch Rexroth

specialists.

▶ In addition, a pressure relief valve is required in the hydraulic system as

back-up. If the axial piston unit is equipped with a pressure cut-off and/or
pressure controller, this is not an adequate safeguard against pressure overload.

Danger due to suspended loads!

Risk of death or injury, or property damage!
Improper transportation may cause the axial piston unit to fall down and lead to
injury, e.g. crushing or fracture, or damage to the product.

▶ Make sure that the load bearing capacity of the lifting device is sufficient to

safely bear the weight of the axial piston unit.

▶ Never step or grip under suspended loads.

▶ Ensure a stable transport position.

▶ Use your personal protective equipment (e.g. safety goggles, safety gloves,

suitable working clothes, safety shoes).

▶ Use suitable lifting devices for transport.

▶ Observe the prescribed position of the lifting strap.

▶ Observe the national laws and regulations on occupational health and safety,

and transportation.

«
...
9
10
11
12
13
...
»

Содержание Rexroth 10 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth 10 Series

Бренд: Tacx Страницы: 2

Бренд: C.E. Nierhoff & Co Страницы: 7

Бренд: GALBIATI Страницы: 20

Бренд: Bang & Olufsen Страницы: 2

Бренд: T-Rex Страницы: 13

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

ESTETICA E70 Vision

Бренд: KaVo Страницы: 48

Бренд: Kaya Safety Страницы: 5

Бренд: XTA Страницы: 20

Бренд: Kawai Страницы: 166

Бренд: Land Pride Страницы: 32

Бренд: NanoVibronix Страницы: 2

Бренд: NanoVibronix Страницы: 32

Shapes Hexagons

Бренд: Nanoleaf Страницы: 27

ENET-232 Series

Бренд: National Instruments Страницы: 105

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды