Bosch Greentherm 9800 SECO 199 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 52

background image

6 720 817 281 (2017/05)

Greentherm 9800 SEO 160/199 | SECO 199

Appliance details | 9

3.3

Unpacking the heater

The heater is default-set by the manufacturer to operate
with Natural Gas, for use with Liquid Propane, follow the
conversion instructions in section 10.13. Before installing
the unit, be certain you have the heater correctly set for
your type of Gas - Propane or Natural Gas.

Identification

labels are found on the shipping box, and on the rating plate
which is located on the left side panel of the cover.

Fig. 2

Rating plate

[A]

Serial number

[B] Type of gas (Natural gas by default)

3.3.1 The box includes

•

Water Heater

•

LP Conversion Kit

•

Bracket and screws for wall hanging the heater

•

Installation manual (manual can be downloaded at
www.boschheatingandcooling.com)

The Greentherm 9800 SEO/ SECO is not approved or
designed for:

•

Manufactured (mobile) homes, boats or any mobile
installation. (Modular homes are acceptable for
installation).

•

Use above 10500 ft A.S.L. altitude.

Applications where inlet water temperature is higher than

140 °F (60 °C) for Residential appliances or 180 °F (82 °C)

for Commercial appliances.

In these applications a 3 way valve or thermostatic mixing

valve must be installed before the appliance's water inlet

connection.

•

Booster applications.

3.3.2 Remove front cover

▶ Loosen two Phillips head screws located on bottom of

cover (fig. 3).

Fig. 3

Loosen two Phillips head screws

▶ Lift the front cover to remove from the appliance.
▶ Install the appliance vertically with the plumbing

connections facing the ground.

In preheated inlet water applications (i.e.
solar preheat), activation flow rate will vary
depending upon the unit set point, inlet
water temperature and the demand flow rate
thru the unit. Please consult Bosch for
further details to determine if this will
function in your application.

«
...
7
8
9
10
11
...
»

Содержание Greentherm 9800 SECO 199





















































Отзывы:

Нет отзывов

Похожие инструкции для Greentherm 9800 SECO 199

Бренд: Patron Страницы: 8

Бренд: YGHP Страницы: 14

Бренд: IBC Страницы: 22

Бренд: NARVI Страницы: 24

Бренд: Fagor Страницы: 4

Бренд: Fagor Страницы: 4

Бренд: Fagor Страницы: 26

Бренд: Fagor Страницы: 4

Бренд: Fagor Страницы: 12

Бренд: laguna Страницы: 24

Бренд: VacPak-It Страницы: 9

Бренд: Quantum Страницы: 20

Бренд: Zoeller Страницы: 12

Бренд: Watts Страницы: 8

Bell & Gossett ecocirc XL Series

Бренд: Xylem Страницы: 62

Бренд: Dex Страницы: 24

Бренд: Enerpac Страницы: 40

Бренд: thermalpanel Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды