Bosch Greentherm 9800 SECO 199 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 52

background image

6 720 817 281 (2017/05)

Greentherm 9800 SEO 160/199 | SECO 199

Electrical connections | 25

6.6

Measuring gas pressure

6.6.1 Gas supply pressure

Confirm gas pressure upon installation.

Connecting manometer

▶ Shut off gas supply at installer supplied shutoff valve for

this water heater.

▶ Locate the inlet gas pressure test port (see Fig.19).
▶ Loosen the screw inside test port fitting (do not remove)

and connect the manometer tube to the test port (see
fig. 19).

Static Pressure Test

▶ Turn the gas supply back on.
▶ Record the static gas pressure reading in table 12.

Dynamic Pressure Test

▶ Turn ON the appliance.
▶ Access menu

P1 Max. Power

, see chapter 10.11.2.

Note: While in this mode the appliance will run constantly at
maximum power and allow maximum water flow.

For inlet gas pressure adjustment consider the following table:

▶ Operate all other gas appliances (except heater) on the

same gas piping system at maximum output.

▶ Open all hot water taps to achieve a flow rate of at least 6

gallons per minute. (1 tub and 2 sinks should be sufficient).
If heater goes back to P2, open more hot water fixtures to
allow sufficient flow and access to P1.

▶ Record the lowest operating gas pressure reading in

▶ Turn OFF the appliance.
▶ Shut off gas supply.
▶ Disconnect the manometer tube from the test point.
▶ Tighten the screw inside test point fitting.

Gas pressures lower than 3.5" W.C. for Natural Gas or 8" W.C.
for LPG may result in reduced power output.

Fig. 19

Gas pressure test port

[1] Gas pressure measuring point

7

Electrical connections

7.1

Electrical power supply

Gas type

NG

LPG

Inlet gas pressure

3.5” WC

8” WC

Table 11 Minimum inlet gas pressure under full operation

Gas pressure

Date

Static Gas Pressure Reading

Dynamic Gas Pressure
Reading

Table 12 Inlet gas pressure readings

WARNING:

▶ For safety reasons, disconnect the

power supply cord to the water heater
before any service or testing is
performed.

WARNING:

▶ For safety reasons install a proper

waterproof outlet.

WARNING:

▶ This water heater must be electrically

grounded in accordance with the most
recent edition of the National Electrical
Code. NFPA 70. In Canada, all electrical
wiring to the heater must be in
accordance with local codes and the
Canadian Electrical Code, CSA C22.1
Part 1. Do not rely on the gas or water
piping to ground the metal parts of the
heater.

«
...
23
24
25
26
27
...
»

Содержание Greentherm 9800 SECO 199





















































Отзывы:

Нет отзывов

Похожие инструкции для Greentherm 9800 SECO 199

Бренд: Eccotemp Страницы: 56

Бренд: Sanden Страницы: 20

Powersaver Dual Flexi

Бренд: Sangamo Страницы: 2

Бренд: Zip Страницы: 18

Бренд: ZIPPER MASCHINEN Страницы: 20

Бренд: VEAB Страницы: 6

Бренд: Gasmate Страницы: 20

Бренд: Clarke Страницы: 16

Бренд: EUROM Страницы: 116

StreetHeat SR-28

Бренд: INTEGRATED PAVING CONCEPTS Страницы: 21

Бренд: Ulvac Страницы: 27

TriScroll 620 Series

Бренд: Agilent Technologies Страницы: 26

Бренд: Expo Börse Страницы: 53

Бренд: Homa Страницы: 72

REMINGTON REM-16-TTC-O

Бренд: Pinnacle Climate Technologies Страницы: 32

Бренд: True North Страницы: 20

FastHeat Digital 14160

Бренд: Kerbl Страницы: 32

Бренд: Annovi Reverberi Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды