Bosch Greentherm 9800 SECO 199 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 52

background image

6 720 817 281 (2017/05)

Greentherm 9800 SEO 160/199 | SECO 199

Installation instructions | 21

6.4

Domestic hot water recirculation with
external pump

Direct recirculation through the tankless water heater is
permissible, however, the heat exchanger warranty is reduced;
see warranty at www.boschheatingandcooling.com.
The following drawings are provided to illustrate possible
recirculation designs. These schematics are for illustration only
and must not be used for actual Installation without
appropriate engineering and technical advice from a properly
licensed professional in the locality where the installation is
made.

This appliance has been designed to permit recirculation by
controlling an external pump. For this function, the external
pump must be electrically connected to the appliance - Bosch
cable accessory is available. All the features of recirculation
can be used with the Bosch remote control.

Fig. 15

Recirculation application with a dedicated return
line

[1] Cold water supply
[2] Check valve field supplied
[3] Circulator pump field supplied
[4] Expansion tank field supplied
[5] Circulator cable accessory
[6] PRV
[7] Shutoff valves field supplied
[8] Greentherm 9800 SEO / SECO

Fig. 16

Recirculation application using the cold water line
and cross-over valve

[1] Cold water supply
[2] Check valve field supplied
[3] Circulator pump field supplied
[4] Expansion tank field supplied
[5] Circulator cable accessory
[6] PRV
[7] Shutoff valves field supplied
[8] Greentherm 9800 SEO / SECO
[9] Cross-over valve, field supplied

6.4.1 Recirculation options

House Recirculation

This recirculation option uses the appliance's NTC sensor along
with the optional schedule to control the pump.

Tank loading

This recirculation option gives the option of using one of three
temperature sensors to control the recirculation option. The
scheduling option is not available for tank loading, except for
commercial models.

•

External NTC - 7 736 504 583

– Only compatible with Bosch cable/sensor accessory

(7736504583).

•

Aquastat - 7 736 504 584

– The aquastat connector kit (7736504584) must be

used to connect a field supplied aquastat to the
appliance.

Recirculation menus for Greentherm 9800
SE O are only available with the Bosch
remote control.

Recirculation application showed in fig. 16 is
for Greentherm 9800 SEO/SECO.
Models with build-in pump cannot be used.

«
...
19
20
21
22
23
...
»

Содержание Greentherm 9800 SECO 199





















































Отзывы:

Нет отзывов

Похожие инструкции для Greentherm 9800 SECO 199

Бренд: Dux Страницы: 20

Coldrink series

Бренд: Everpure Страницы: 4

Бренд: K Tool International Страницы: 20

Бренд: BN Thermic Страницы: 8

Бренд: DeLonghi Страницы: 4

Бренд: Cocoon Concept Страницы: 5

Comfort SC-FH53015

Бренд: Scarlett Страницы: 8

Бренд: DanPure Страницы: 8

Бренд: Essentielb Страницы: 29

105STS 90 -1.5"

Бренд: Canature Страницы: 94

Milton Roy Milroyal Series

Бренд: Accudyne Industries Страницы: 68

Бренд: Easylife Страницы: 3

Бренд: SAMUEL JACKSON Страницы: 29

Бренд: WaterLogic Страницы: 46

HydroChill HCF90NZ

Бренд: Zenith Страницы: 36

Бренд: Flagro Страницы: 25

Бренд: pleasant hearth Страницы: 10

Бренд: fluid-o-tech Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды