Bosch AutoDome Скачать руководство пользователя страница 11

Страница: 11 / 24

Photo 4I Interior of ENV-PA1 Series Showing Fiber Optic

Cable Connector

NOTES:

Daisy chaining of the biphase is not possible when
using fiber optic accessories.

Verify that the BNC from the fiber board is connected
to the VIDEO OUT connector (as shown in PHOTO
4I).

4.3.5. For 24 VAC models, connect the VIDEO cable directly

into the male BNC connector provided with the pen-
dant arm (see PHOTO 4J).

Photo 4J

4.3.6. Feed the POWER and DATA cables up through the

pendant arm (as shown in PHOTO 4J).

4.3.7. Wire the 9-pin connector as shown in FIGURE 1.

Figure 1

NOTE:

If the dome’s Biphase is wired in a star configuration,

or is the last dome on a daisy chain, a 110

Ω

terminating resistor

(included) is necessary across pin 8 (C+) and pin 9 (C-).

4.4

Connecting the Pendant Arm to the Box

4.4.1. Feed the prewired connector and video cable up

through the pendant arm (as shown in PHOTO 4K).

Photo 4K

4.4.2. Align the carriage bolts on the pendant box with the

holes in the pendant arm, and slip the arm onto the
box.

4.4.3. Secure the acorn nuts (supplied) onto each bolt and

tighten.

4.5

Attaching the Dome to the Pendant Arm
Mount

4.5.1. Attach the installation-assist cable to the eyehook

(PHOTO 4L) on the top of the dome.

Photo 4L

4.5.2. Connect the 9-pin connector (previously wired in

SECTION 4.3.3, as shown in PHOTO 4L), and
tighten the retaining screws.

4.5.3. Connect the VIDEO (BNC) cable to the VIDEO (BNC)

connector.

*If the internal slide switch (see FIGURE 1, at left), is
set for RS-485 operation, then RXD function as DATA
(+), and TXD functions as DATA (–).

Installation

Page 11 of 24

Fiber Connects Here

Video Out Cable

Male BNC Provided

Feed Wires Through Here

C–

Biphase
Ground
B
Biphase –

RS-232
Ground
RS-232/*
RS-232/*

24 VAC Neutral
Indoor Pendant - Not Connected
EnviroDome

- 24 VAC Heater

24 VAC Hot

C+ GND RXD TXD GND H

24 VAC

CONTROL CONNECTOR

Retaining

Screw

Feed Wires Through Here

BNC Connector

Eyehook

8-Pin Alarm

Connector

9-Pin Control

Connector

Installation Assist Cable

Содержание AutoDome

























Результаты поиска

Содержание AutoDome

Отзывы:

Похожие инструкции для AutoDome

Бренды по названию

Популярные бренды

Bosch AutoDome, Руководство по монтажу

Результаты поиска

Содержание AutoDome

Отзывы:

Похожие инструкции для AutoDome

Бренды по названию

Популярные бренды