BOMBARDIER BD-100-1A10, Руководство по эксплуатации

Страница: 480 / 544

NAVIGATION
Volume 2 Flight Crew Operating Manual May 06/2005
17-01-04
CSP 100-6
REV 2
VHF NAVIGATION SYSTEM (Cont)
TRANSPONDER/TCAS OPERATION
The radio menu provides basic transponder and TCAS control. The TRANSPONDER/TCAS CONTROL menu provides
control display for other transponder and TCAS operations. The active beacon code, TCAS mode, and TCAS altitude limits
selection that show on the left of the TRANSPONDER/TCAS CONTROL menu are identical to the TRANSPONDER/
TCAS display on the radio menu. Two transponders are installed. The active transponder selection is used to select the de-
sired transponder. When the active transponder is set to ATC 1, the pilot’s side transponder is active. When the active tran-
sponder is set to ATC 2, the copilot’s side transponder is active.
To tune the TRANSPONDER/NAV radio execute the following steps:
1. Push the RADIO button on the DCP to show the radio menu on the MFD if another menu/list is active.
2. Turn the MENU knob on the DCP to move the selection box to the TRANSPONDER/TCAS display on the radio
menu.
3. Push the RADIO button on the DCP to show the TRANSPONDER/TCAS CONTROL menu on the MFD.
4. The following operations are performed on the TRANSPONDER/TCAS CONTROL menu:
- Select TCAS traffic altitude mode.
-Turn the MENU knob to move the selection box to the TRAFFIC control
-Turn the DATA knob or push the PUSH SELECT button to select traffic altitude mode REL (relative) or ABS
(absolute)
- Select the active transponder.
-Turn the MENU knob to move the selection box to the transponder control
-Turn the DATA knob or push the PUSH SELECT button to select ATC 1 or ATC 2 as the active transponder
- Set the Flight ID
-Turn the MENU knob to move the selection box to the Flight ID control
-Turn the TUNE knobs to set the desired Flight ID characters
- Select the ATC/TCAS TEST mode.
-Turn the MENU knob to move the selection box to the TEST control
-Turn the DATA knob or push the PUSH SELECT button to select the TEST mode
ADF RADIO OPERATION
The radio menu provides basic ADF radio tuning. The ADF CONTROL menu provides control display for other ADF radio
operations. Each ADF radio installed on the aircraft has its own ADF CONTROL menu. If only one ADF radio is installed,
it shows on both the on-side and cross-side menus, and will be labeled ADF CONTROL with no numerical designator. The
active frequency, recall frequency, and antenna mode that show on he left of the ADF CONTROL menu are identical to the
ADF display on the radio menu.
To set the ADF modes execute the following steps:
1. Push the RADIO button on the DCP to show the radio menu on the MFD if another menu/list is active.
2. Turn the menu knob on the DCP to move the selection box to the ADF radio (ADF 1 or ADF 2) display on the
radio menu.
3. Push the RADIO button on the DCP to show the ADF CONTROL menu on the MFD.
4. The following operations are performed on the ADF CONTOL menu:
- Select the ADF/ANT mode.
-Turn the MENU knob to move the selection box to the MODE control
-Turn the DATA knob or push the PUSH SELECT button to select ADF or ANT mode
- Select BFO mode.
-Turn the MENU knob to move the selection box to the BFO control
-Turn the DATA knob or push the PUSH SELECT button to select ON or OFF for the BFO mode
- Select ADF TEST mode.
-Turn the MENU knob to move the selection box to the TEST control
-Turn the DATA knob or push the PUSH SELECT button to select the TEST mode
V 2