background image

20 

 

− Relative humidity 45% through 80%; 

− Ambient temperature 15

°

C through 35

°

C; 

− Atmospheric pressure 630 mm Hg through 800 mm Hg (84 through 106.7 kPa). 

3.3.4

 

While  inspecting  the  module,  always  shut  off  the  module’s  power  before  connecting  and 

disconnecting its external circuits. 
3.3.5

 

Testing procedures include inspecting operability and testing indication in the Indication Test 

mode. 
3.3.6

 

Preparations for testing the module includes: 

a)

 

Check the package conditions and unpack the module; 

b)

 

Check  the  delivery  to  comply  with  Section  1.3  of  this  manual,  presence  and  content  of 

the accessory kit, serial number of the module and its production date to comply with those 
ones specified in the operation manual; 
c)

 

Ensure the module enclosure is not damaged; 

d)

 

Shake the module and ensure there are no foreign bodies within it; 

e)

 

Ensure that the terminal blocks are fastened properly. 

3.3.7

 

 To  test  operability  of  the  module,  please  follow  the  instructions  of  Section  3.4  of  this 

manual. 

3.4

 

Performance Testing 

3.4.1

 

Inspecting Operability 

To  inspect  the  module,  use  an  S2000M  panel.  Connect  the  module’s  RS-485  circuits  and  power 

circuits to the relevant terminals of the panel. 

Connect a milliammeter in series with the power circuit of the module. 
Apply power to the module and the panel. 
The power LED of the module   (the upper LED near the device name) shall 

show green solid light within 2 s. 

Measure  the  current  consumed  by  the  module.  Its  value  shall  not  exceed 

200 mA. 

Within a minute since powering on, the panel shall display a message about 

detecting a device with the network address currently assigned to the S2000-BKI 
(factory  value  of  the  module  address  is  127).  Figure 3  shows  the  display  of  the 
S2000M panel with the relevant message. 

If several messages accumulated by the module have been received by the panel, you can browse 

them by the arrow buttons «

» and «

» on the S2000M.  

3.4.2

 

Checking in the Indication Test mode 

Initiate the self-diagnostic mode for the module by selecting the Indication Test command in the 

S2000M menu followed by selecting the module address (the factory address of the module is 127); see 
the S2000M user’s manual for details. 

If the module is operable, its indicators turn on in the following order: 
a)

 

The columns of LEDs “1” – “60” turn on with amber one-by-one; the indicator FIRE 2 turns on 

with amber; the reader LED turns on with amber; the indicators ARMING FAILED, DISABLED, FAULT 
turn on with amber; 

b)

 

The  rows  of  LEDs  “1” – “60”  turn  on  with  amber  one-by-one,  FIRE  2,  FIRE,  INTRUSION, 

PANIC  ALARM,  the  reader  LEDs  turn  on  with  red,  then  ,  FIRE  2  (with  changing  color),  FIRE, 
PREALARM, INTRUSION, PANIC ALARM, ARMING FAILED, FAULT, DISABLED, and the reader 
LED (with changing color) turn on one-by-one; 

Figure 3 

Содержание S2000-BKI






















Отзывы: