BNF Blade 500 3D Скачать руководство пользователя

Страница: 10 / 64

Rudder Control Test

Cyclic Control Test

1.  Disconnect any two main motor wires from the ESC.
2.  Power on the transmitter.
3.  Make sure the transmitter is in Normal Mode.
4.  Connect the flight battery to the ESC.
5.  Move the rudder control to the right.  The tail rotor blades move as

shown. If they do not move as shown, reverse the rudder channel in the

transmitter (refer to your transmitter manual for instructions).

6. Release the rudder control. Quickly turn the helicopter nose to the left.

The tail blades move in the same direction as right rudder input. If they

do not move as shown, change the position of the reverse switch on the

gyro.

MODE 2

MODE 1

Elevator

ail

Side View

Aileron

ail

Rear View

ail

Collective Pitch

ail

Rear View

Place the helicopter on a clean and flat ground surface (concrete or asphalt)

outdoors and free of obstructions. Always stay clear of the moving rotor blades.

1. Disconnect any two main motor wires from the ESC.
2. Turn the transmitter on and make sure the flight mode is set to normal.

3. Connect the EC3 battery connector to the helicopter’s ESC. Do not allow

the helicopter to move until the red LED on the gyro is solid.

4. Check the swashplate directions to ensure they are moving in the

correct direction. Please refer to the diagrams above for reference.

Blade Tracking (Blade Helicopters, 450-size and Larger)

WARNING:

Always maintain a safe distance of at least 15 meters

(45 feet) when checking the main rotor blade tracking.

To check the blade tracking:

1. Put the helicopter in a hover at an altitude near eye height.

2. Watch the movement at the blade tips. Both blades should travel in the

same plane.

3. If one blade tip appears to be higher than the other, land the helicopter,

disconnect the flight battery and adjust the blade linkages.

4. Repeat Steps 1 through 3 until both blades are moving in the same

plane.

Содержание Blade 500 3D

































































Результаты поиска

Содержание Blade 500 3D

Отзывы:

Похожие инструкции для Blade 500 3D

Бренды по названию

Популярные бренды

BNF Blade 500 3D, Инструкция по эксплуатации

Результаты поиска

Содержание Blade 500 3D

Отзывы:

Похожие инструкции для Blade 500 3D

Бренды по названию

Популярные бренды