background image

Introduction 

We are confident that you will be delighted with your Blue Seal Gas Salamander, and it will become a most  

valued appliance in your commercial kitchen. 

 

To ensure you receive the utmost benefit from your new Blue Seal Gas Salamander, there are two  

important things you can do. 
 

Firstly: 

Please read the instruction book carefully and follow directions given.  The time taken will be well spent. 

 

Secondly: 

If you are unsure of any aspect of the installation, instructions or performance of your appliance,  

contact your BLUE SEAL dealer promptly.  In many cases a phone call could answer your question. 

 
CE Only: 

These instructions are only valid if the country code appears on appliance.  If code does not appear on 

appliance, refer to supplier of this appliance to obtain technical instructions for adapting appliance to 

conditions for use in that country. 

 
 
 

G

REAT

 

CARE

 

MUST

 

BE

 

TAKEN

 

BY

 

THE

 

OPERATOR

 

TO

 

USE

 

THE

 

EQUIPMENT

 

SAFELY

 

TO

 

GUARD

 

IT

 

AGAINST

 

RISK

 

OF

 

FIRE



T

HE

 

APPLIANCE

 

MUST

 NOT 

BE

 

LEFT

 

ON

 

UNATTENDED



I

T

 

IS

 

RECOMMENDED

 

THAT

 

A

 

REGULAR

 

INSPECTION

 

IS

 

MADE

 

BY

 

A

 

COMPETENT

 

SERVICE

 

PERSON

 

TO

 

ENSURE

 

CORRECT

 

AND

 

SAFE

 

OPERATION

 

OF

 

YOUR

 

APPLIANCE

 

IS

 

MAINTAINED



DO NOT 

STORE

 

OR

 

USE

 

GASOLINE

 

OR

 

OTHER

 

FLAMMABLE

 

VAPOURS

 

OR

 

LIQUIDS

 

IN

 

THE

 

VICINITY

 

OF

 

THIS

 

OR

 

ANY

 

OTHER

 

APPLIANCE



DO

 

NOT

 

SPRAY

 

AEROSOLS

 

IN

 

THE

 

VICINITY

 

OF

 

THIS

 

APPLIANCE

 

WHILE

 

IT

 

IS

 

IN

 

OPERATION

Warning 

 

 
 



This appliance is for professional use and is only to be used by qualified 
persons. 



Only authorised service persons are to carry out installation, servicing or gas 
conversion operations. 



Components having adjustments protected (e.g. paint sealed) by the 

 

manufacturer should not be adjusted by the user / operator. 

Caution 

 
 

I

MPROPER

 

INSTALLATION

ADJUSTMENT

ALTERATION

SERVICE

 

OR

 

MAINTENANCE

 

CAN

 

CAUSE

 

PROPERTY

  

DAMAGE

INJURY

 

OR

 

DEATH

.  R

EAD

 

THE

 

INSTALLATION

OPERATING

 

AND

 

MAINTENANCE

 

INSTRUCTIONS

  

THOROUGHLY

 

BEFORE

 

INSTALLING

 

OR

 

SERVICING

 

THIS

 

APPLIANCE

Warning 

 
 
 
INSTRUCTIONS

 

TO

 

BE

 

FOLLOWED

 

IN

 

THE

 

EVENT

 

THE

 

USER

 

SMELLS

 

GAS

 

ARE

 

TO

 

BE

 

POSTED

 

IN

 

A

 

PROMINENT

 

LOCATION

.  

THIS

 

INFORMATION

 

SHALL

 

BE

 

OBTAINED

 

BY

 

CONSULTING

 

THE

 

LOCAL

 

GAS

 

SUPPLIER

Warning 

Содержание G91

























Отзывы: