background image

OM-APEX E V1.06

November 19, 2012

Page 3

APEX CBT

INTRODUCTION

To Our Valued Customers

Dear Customer:

Th

  ank you for purchasing a 

Blaze King APEX CBT

 catalytic wood burning furnace (hereaft er 

referred to as “furnace”).

Th

  is owner's manual explains the steps required to safely assemble, install, operate, and maintain 

your new furnace.  Please carefully read these requirements for safe installation and proper 
operation before installing and using your furnace.

Obtain permits from the Building Inspector or Fire Department, if local laws require.  Check local 
building and fi re codes before installing your heater.  When you have completed the installation, 
have it checked by your local inspector.  Disregarding inspection and code requirements may 
jeopardize your homeowner's insurance.  Since some insurance carriers require notifi cation of a 
stove installation, contact your insurance agent.  We want your Blaze King to give you a lifetime 
of trouble-free operation.

While we have made every eff ort to make these instructions as complete as possible, some 
installation or operating conditions may not be covered.  If you have any questions that are not 
answered here, contact your Blaze King dealer, Local Building Inspector, Fire Department, or our 
customer service department at Blaze King.  In the USA please call (509)-522-2730 or in Canada 
please call (250)-493-7444.

Th

  e Management and Employees of

Blaze King Industries, Inc

Содержание APEX CBT









































Отзывы: