background image

OM-APEX E V1.06

November 19, 2012

Page 16

APEX CBT

INSTALLATION INSTRUCTIONS - Venting cont.

CONNECTION TO A MASONRY CHIMNEY

Masonry chimney***
Ensure that a masonry chimney meets the minimum 
standards (NFPA) by having it inspected by a 
professional. Make sure there are no cracks, loose 
mortar or other signs of deterioration and blockage. 
Have the chimney cleaned before the stove is 
installed and operated. When connecting the stove 
through a combustible wall to a masonry chimney, 
special methods are needed.

In Canada,
Th

  e wall cut away is to provide 18” clearance for the 

connector. Th

  e resulting space must remain empty. 

A fl ush mounted sheet metal cover may be used on 
one side only. If covers are to be used on both sides, 
each cover must be mounted on noncombustible 
spacers at least 1” clear of the wall.

***Blaze King recommends the use of a Stainless 
steel liner, preferably insulated, inside a masonry 
chimney. Th

  is to maintain proper draft  and overall 

better operation of  the unit.

Your local dealer or local jurisdiction can provide details of approved methods of passing a chimney connector 
through a combustible wall in your area. In USA, the National Fire Protection Association has minimum 
standards to comply with. In Canada , this type of installation must conform to CAN/CSA-B365, Installation 
Code for Solid Fuel Burning Appliances and Equipment.

Содержание APEX CBT









































Отзывы: