14 • ENGLISH
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making
any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool.
Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by Black &
Decker, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following
symbols:
ADDITIONAL POWER TOOL SAFETY
WARNINGS
f
Wear ear protectors. Exposure to noise can cause
hearing loss.
f
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
f
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and shock
the operator.
f
Never use a chisel accessory in rotary mode. The
accessory will bind in the material and rotate the drill.
f
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it
unstable and may lead to loss of control.
f
Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
f
Avoid touching the tip of a drill bit just after drilling, as
it may be hot.
f
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to
ensure that they do not play with the appliance.
f
The intended use is described in this instruction
manual. The use of any accessory or attachment
or performance of any operation with this tool other
than those recommended in this instruction manual
may present a risk of personal injury and/or damage
to property.
f
Use a face or dust mask whenever the operations may
produce dust or flying particles.
Warning! Additional safety warnings for grinding,
sanding, wire brushing, polishing or abrasive cutting- off
operations.
f
Wear ear protectors. Exposure to noise can cause
hearing loss.
f
Use auxiliary handles supplied with the tool. Loss
of control can cause personal injur.
f
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord.
Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool “live” and
could give the operator an electric shock.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
J ........
Joules
Hz ....... Hertz
W ........ Watts
min ..... minutes
bpm ........ Beats per
minute
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
