BIOTRONIK Evia HF Скачать руководство пользователя страница 25

Страница: 25 / 138

Chapter 5

Programmable Parameters

Evia HF / HF-T Technical Manual

PAGE 17

The triggered pacing mode fixes the AV delay to 180 ms and does not provide a safety AV delay.
Pacing modes with triggered response may be indicated in the presence of interference signals to

prevent inappropriate pulse inhibition. They may also have diagnostic application for ECG identification

of sense events as an alternative to marker signals. Triggered pacing may also be used for

hemodynamic as well as electrophysiologic studies and for termination of tachycardias by non-invasive

triggering of pulse generator pulses with chest wall stimuli generated by an external pulse generator.

CAUTION

Programmed to Triggered Modes

When programmed to triggered

modes, pacing rates up to the programmed upper limit may occur in

the presence of either muscle or external interference.

Triggered Modes

While the triggered modes (DDT, VVT, and AAT) can

be programmed permanently, the use of these modes is intended as

a temporary setting in situations where maintaining the programming

head in place would be impossible or impractical (i.e., during exercise

testing or extended Holter monitoring) or as a short term solution to

pulse generator inhibition by extracardiac interference. To avoid the

potential for early battery depletion, it is important that the triggered

modes are not used for long term therapy, and that the pulse generator
is returned to a non-triggered permanent program.

5.2 Rate Related Functions

The availability of parameters and parameter values is determined by the software used for

programming/ interrogating the pulse generator.

5.2.1 Basic Rate

The Basic rate parameter (

Figure 2

) sets the lower pacing rate for the pacemaker and may be

programmed from 30 bpm to 200 bpm. Evia HF / HF-T will allow pacing lower than the programmed

rate when the parameter Hysteresis is enabled. The Hysteresis parameter is found under Basic rate /

Night rate.
Programming conflicts for Basic rate occur when Atrial and/or Ventricular Capture Control is

programmed ON. When capture control is programmed ON, the basic rate is limited to 100 bpm.

Figure 2: Basic Rate/Night Rate Screen with Default Settings

Содержание Evia HF











































































































































Результаты поиска

Содержание Evia HF

Отзывы:

BIOTRONIK Evia HF, Техническое руководство, Страница: 25 / 138

Результаты поиска

Содержание Evia HF

Отзывы: