BIOLABO Diagnostics KENZA 240 TX Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 56

BIOLABO Diagnostics KENZA 240 TX Скачать руководство пользователя страница 11

- 11 -

2.1 Unpacking the Kenza 240 TX / ISE

Carefully inspect the package for any sign of shipping damage. The box contains a shock detector that
detects every shock higher than 50G. Check it before opening the box.

Caution! If package or contents are damaged, put a claim in with the freight forwarder and notify
BIOLABO or your local agent.

Open the package and remove the accessories and the instrument. Make sure the contents are complete. A
list of the accessories is supplied on the Check-list enclosed in the packing.

Keep the original package for possible later transport.

Caution!

Direct or indirect damage to the instrument caused by using improper packaging during

shipment is not covered by BIOLABO’s liability or warranty.

2.2 Installation of the instrument

This is the procedure to install the KENZA 240TX or KENZA 240 ISE analyser. Please, in case of any doubt
or ambiguity in understanding this procedure, contact your nearest distributor since an improper installation
may damage seriously the instrument.

•

Place the instrument on a stable and vibration-free support. Avoid its placing near sources (e.g.
heaters, ovens, under high power lamps), under direct sunlight, near strong electromagnetic sources
(e.g. motors). The optimal operational temperature range is 15-32°C and humidity must be under
70% at 32°C.

•

Let a sufficient place between the rear panel of the instrument and the wall to allow good ventilation.

•

Before connecting the instrument to the power
supply, make sure that it is switched off. In this
case, the switch on the backside of the instrument
must be in the 0 position.

•

Remove the soft protection of the arms

•

Install the arm cover as describe in the enclosed
protocol

•

Install Waste and Water tanks.

•

Install reagent and sample trays.

•

Verify that all these points have been respected

2.3 Installation of the software

Insert the CD-ROM supplied with the instrument in the CD-ROM drive of the computer.

The CD-ROM has an autorun and should start automatically. Otherwise, explore the CD-ROM via the
explorer and double-click on the file “setup.exe”.

Then follow the instructions on screen.

N

N

o

o

t

t

e

e

: It’s better to install speakers on the computer to get smooth alarms. If the computer has no speaker,

the alarms will be heard via the motherboard buzzer.

WARNING: make sure the chosen supply socket has a suitable earth
connection, since it is required to assure user’s safety during
instrument usage.

«
...
9
10
11
12
13
...
»

Содержание KENZA 240 TX

























































Отзывы:

Нет отзывов