Billy Goat Hurricane Z3000 Скачать руководство пользователя страница 30

Страница: 30 / 48

Not for

Reproduction

billygoat.com

Maintenance Procedures

Search for leaks with a piece of cardboard. Protect
hands and body from high pressure

uids.

IMPORTANT:

Check oil level in reservoir tank when

oil is cold.

Do not over

ll oil reservoir tank. Oil will expand during

operation and could over

ow.

1. Park machine safely.

2. Allow engine to cool.

3. Clean reservoir and cap.

4. Sight through reservoir and ensure oil level is at

the full cold line. If oil is low, add oil to bring oil
level no higher than FULL COLD mark on tank.

NOTE:

If oil is above FULL COLD line, drain oil to

proper level.

5. Tighten

cap.

Changing Hydraulic Oil and Filters

The transaxles are designed with an external

lter for

ease of maintenance. To ensure constant

uid quality

levels and longer life, an initial oil and

lter change at

75 hours, then every 400 hours thereafter.

The following procedure can be performed with the
transaxles installed in the machine, and the machine
on level ground.

1. Park machine safely. Engage the parking brake.

2. Allow engine and transaxles to cool.

3. Jack machine up from rear. Use blocking to sup-

port machine.

4. Remove both rear tires. Apply the bypass valves

for both transaxles.

CAUTION:

Skid plate is heavy.

5. Remove six 3/8-16 x 3/4 bolts that fasten skid

plate in position.

Use

oor jack to support the skid plate. Lower

jack and remove from under unit.

6. Remove toe kick to access the hydraulic

lters,

set aside.

Hydraulic Oil Filter

(Not Visible Behind Filter Guard)

Drain Plug

Transaxle Drain Plug and Hydraulic Oil Filter.

7. Remove

the

three

lter guard screws and

lter

guard. Clean any loose debris from around the
perimeter of the

lter. Place drain pan beneath

the oil

lter.

8. Remove

the

oil

lter from the transaxle. Dispose

of used

lter properly.

9. Remove the drain plug from the transaxle, allow

all

uid to drain.

10. After the oil has drained, wipe the

lter base sur-

face off and apply a

lm of new oil to the gasket

of the new replacement

lter.

11. Replace the drain plug.

12. Install the new

lter by hand, turn 3/4 to one full

turn after the

lter gasket contacts the

lter base

surface. Do not use a wrench.

13. Re-install the

lter guard with three screws.

Torque screws to 65 in. lbs.

14. Repeat steps 8-14 on the opposite side transaxle

drive.

15. Remove the purge port plug from the back of the

transaxle. Refer to

Purge Port Plug Location

photo.

Содержание Hurricane Z3000

















































Результаты поиска

Содержание Hurricane Z3000

Отзывы:

Похожие инструкции для Hurricane Z3000

Бренды по названию

Популярные бренды

Billy Goat Hurricane Z3000, Руководство пользователя

Результаты поиска

Содержание Hurricane Z3000

Отзывы:

Похожие инструкции для Hurricane Z3000

Бренды по названию

Популярные бренды